Filter
Top Products
46
(Continued)
0dB
2
3
4
7
8
Synchro recording
W - -12WWW-4WWWW 0 W >W
R
L
W -
-12WWW-4WWWW 0 W>W
AUX1TWWWWWWWWWWWWWWWW
W - WW
-12WWW-4WWWW 0 W>W
R
L
MDWWWW 1WW
WW 0:00WWWWWY
AUX1TWWWWWWA. MARKWONW
W- WW
-12WWW-4 WWWW 0 W > W
R
L
MDWWWW 1WW
WW 0:00WWWWWY
AUX1TWWWWWW A. MARKWONW
W- WW
-12WWW-4 WWWW 0 W > W
R
L
MDWWWW 1WW
WW 0:00WWWWWY
AUX1TWWWWSOUNDWSYNCRO
W- WW
-12WWW-4 WWWW 0 W > W
R
L
MDWWWW 1WW
WW 0:02WWWWWY
AUX1TWWWWSOUNDWSYNCRO
HH
HH
H Listening to sound from an external unit
To listen to digital sound
1 Press the AUX button so that the AUX OPT. or AUX COAX
display appears.
I Each time the button is pressed, the display will change as follows:
AUX1 AUX2 AUX OPT. AUX COAX PHONO
2 Start playback on the external unit.
3 Adjust the sound level using the VOLUME control of this unit.
Note:
In the following cases, "DIN UNLOCK" appears and playback
sound is muted:
I When the external digital unit is off.
I When there is no digital input from the digital input jack.
To listen to analog sound
1 Press the AUX button so that the AUX 1 or AUX 2 display
appears.
I When connecting an external unit to the "MD IN/AUX1 " terminal at the
front of the main unit, select "AUX1". When connecting to the "AUX2"
terminal at the rear of the main unit, select "AUX2".
2 Adjust the input sound level using the INPUT LEVEL control.
I When the INPUT LEVEL control is turned counterclockwise, no sound
is obtained.
3 Start playback on the external unit.
4 Adjust the volume using the INPUT LEVEL control and VOL-
UME control on this unit.
HH
HH
H Synchro recording
MD recording will start automatically as soon as playback is
started on the external unit. This applies to both digital inputs and
analog inputs.
I The space-cut function will work automatically during synchro record-
ing.
I Synchro recording is available only for recordings from an external
unit.
1 Load a recordable MiniDisc.
2 Press the AUX button to select the auxiliary input .
I Select the input that corresponds to the terminals where the external
unit you want to record from is connected.
I Each time the button is pressed, the display will change as follows:
AUX1 AUX2 AUX OPT. AUX COAX PHONO
To record analog signals, perform steps 3 - 8.
To record digital signals, perform steps 6 - 8.
3 Press the REC button, then start playback on the external unit.
4 Adjust the recording level using the INPUT LEVEL control.
I The maximum level should not exceed 0 dB.
5 Stop playback on the external unit.
6 Press the MD H button.
7 Press the SYNCHRO REC button.
8 Start playback on the external unit.
I Recording will start automatically.
I To stop recording halfway, press the MD H button.
MD
MD
AUX
INPUT LEVEL
REC
AUX
REC
SYNCHRO
REC
VOLUME
DOWN UP
38-58 98.6.23, 10:34 AM46