Pioneer VSX-50 Stereo Receiver User Manual


 
! When using the AS-BT200 only: This unit
complies with Bluetooth Specifications
Ver. 2.1. When this unit and another device
equipped with Bluetooth wireless technology
both comply with Bluetooth Specification Ver.
2.1, pairing of the two may be possible without
the need for inputting a password.
In this case, a passcode may be displayed on
this receiver and on the device equipped with
Bluetooth wireless technology. If this happens,
check that the same passcode is displayed
on this receiver and the device equipped
with Bluetooth wireless technology, then
select YES with the k and l keys and press
ENTER. After this, also perform the connection
operation on the Bluetooth device to be
connected. If the passcode does not match
the code displayed on the Bluetooth device to
be connected, select NO to cancel pairing,
then try starting over.
Press ADPT to set the ADAPTER PORT
input, then conduct the pairing operation on
the Bluetooth wireless technology device.
If pairing is successful, there is no need to
performing the pairing operation below.
! Pair one unit at a time.
! When connecting this receiver by Bluetooth
connections with a device equipped with the
Bluetooth function to listen to music, do not
connect any devices other than this receiver
by Bluetooth connection to the Bluetooth-
equipped device. If a Bluetooth connection is
already established with a device other than
this receiver, disconnect the other device
before connecting this receiver.
1 Press on the remote control,
then press HOME MENU.
2 Select ‘System Setup’, then press
ENTER.
3 Select ‘Other Setup’, then press ENTER.
4 Select ‘Pairing Bluetooth Device’, then
press ENTER.
5 Select the ‘Passcode’ setting you want.
Select the same passcode as the Bluetooth
wireless technology device you wish to connect.
! 0000/1234/8888 – Select the passcode from
these options. These are the passcodes that
can be used in most cases.
! Others – Select to use a passcode other than
those mentioned above.
6 If you selected ‘Others’ in step 5, enter
the passcode.
Use i/j to select a number and k/l to move
the cursor.
7 Follow the instructions displayed on
the GUI screen to conduct pairing with the
Bluetooth wireless technology device.
Switch on the Bluetooth wireless technology
device that you want to make pair, place it near
the receiver and set it to the pairing mode.
8 Check to see that the Bluetooth
ADAPTER is detected by the Bluetooth
wireless technology device.
When the Bluetooth wireless technology device
is connected:
CONNECTED appears in the receiver display.
! The system can display alphanumeric
characters only. Other characters may not be
displayed correctly.
When the Bluetooth wireless technology device
is not connected:
Go back to the passcode setting in step 5. In
this case, perform the connection operation
from the Bluetooth wireless technology device.
9 From the Bluetooth wireless
technology device list, select Bluetooth
ADAPTER and enter the Passcode selected
in step 5.
! The passcode may in some cases be referred
to as PASSKEY or PIN code.
En
34
05 Basic playback
Bluetooth ADAPTER for
Wireless Enjoyment of Music
This receiver
Remote control
operation
Music data
Bluetooth
®
ADAPTER
Bluetooth
wireless
technology
enabled device:
cell phone
Bluetooth wireless
technology
enabled device:
Digital music
player
Device not
equipped with
Bluetooth wireless
technology:
Digital music
player
+
Bluetooth audio
transmitter
(sold commercially)
MASTER
VOLUME
STANDBY/ON
INPUT
SELECTOR
PUSH
OPEN
iPod iPhone iPad
DIRECT
CONTROLSTEREO
ADVANCED
SURROUND
STANDARD
SURROUND
AUTO SURR/ALC/
STREAM DIRECT
PHONES
SPEAKERSCONTROL – MULTI-ZONE – ON/OFF BAND TUNER EDIT TUNE PRESET ENTER
iPod iPhone iPadHDMI
ADVANCED
MCACC
FL OFF
Wireless music play
When the Bluetooth ADAPTER (AS-BT100 or
AS-BT200) is connected to this unit, a product
equipped with Bluetooth wireless technology
(portable cell phone, digital music player, etc.)
can be used to listen to music wirelessly. Also,
by using a commercially available transmit-
ter supporting Bluetooth wireless technol-
ogy, you can listen to music on a device not
equipped with Bluetooth wireless technology.
The AS-BT100 and AS-BT200 models supports
SCMS-T contents protection, so music can also
be enjoyed on devices equipped with SCMS-T
type Bluetooth wireless technology.
Remote control operation
The remote control supplied with this unit
allows you to play and stop media, and perform
other operations.
! It must be necessary that the Bluetooth
wireless technology enabled device supports
AVRCP profiles.
! Remote control operations cannot be
guaranteed for all Bluetooth wireless
technology enabled devices.
Pairing the Bluetooth ADAPTER
and Bluetooth wireless
technology device
“Pairing” must be done before you start play-
back of Bluetooth wireless technology content
using the Bluetooth ADAPTER. Make sure to
perform pairing the first time you operate the
system or any time pairing data is cleared.
The pairing step is necessary to register the
Bluetooth wireless technology device to enable
Bluetooth communications. For more details,
see also the operating instructions of your
Bluetooth wireless technology device.
! Pairing is required when you first use the
Bluetooth wireless technology device and
Bluetooth ADAPTER.
! To enable Bluetooth communication, pairing
should be done with both your system and
Bluetooth wireless technology device.
! If the Bluetooth wireless technology device’s
security code is “0000”, there is no need to
make the security code setting on the receiver.
Press ADPT to set the ADAPTER PORT
input, then conduct the pairing operation on
the Bluetooth wireless technology device.
If pairing is successful, there is no need to
performing the pairing operation below.