Filter
Top Products
RQT8926
83
The settings for the volume balance of the front speakers
(L , R) changes (0 to s12 dB).
≥When headphones are connected (➜ page 86) the
balance will return to 0 dB (center).
∫ To change the subwoofer trim levels
2 When [TRIM SW (SW ch)] is selected, press [34].
The settings for the trim level of the subwoofer changes
(s6 to r6dB).
With only the included front/center speakers and the
subwoofer, you can add a surround sound effect similar to 5.1
ch (Dolby Digital or DTS) to any audio source. You can also
add a surround sound effect to stereo sources such as video
tapes or CDs.
Press [Î VS].
Each time the button is pressed, it switches as shown
below.
≥Set the Dolby Virtual Speaker to “REFERENCE” or
“WIDE”, and if the play source is 2 ch, “Î PL II” will
light up.
[Note]
When “ERROR” is displayed:
In the following cases, “ERROR” is displayed, and you cannot
set the Dolby Virtual Speaker.
–During play, when the selector is set to “DVD/CD” and the
audio source currently playing is in 3.1 ch, 3 ch, 1.1 ch, or
1ch.
–When you are playing content that prohibits D.MIX (down-
mixing)
–When headphones are connected.
This unit can decode the surround signals received through
cable box, digital broadcasting or satellite broadcasts. Refer to
your equipment’s operating instructions for details. Only Dolby
Digital and PCM can be played with this connection.
1 Press [SETUP].
2 Press [34] to select “Other Setup” and press
[ENTER].
3 Press [34] to select “TV Audio Input” and press
[1].
4 Press [ENTER].
5 Press [34] to select “DIGITAL IN” and press
[ENTER].
6 Press [RETURN] to exit the screen.
7 Then press [N SELECT O] to switch the selector to
“TV Audio” as the source.
∫ Selecting to the sound effects
When you select “DIGITAL IN” as the source, you can select
the following sound effects. (These functions only work with
Dolby Digital or PCM, excluding Audio Mode, which only works
with Dolby Digital Dual Mono.)
1 Press [SUB MENU].
2 Press [34] to select the effect that you want to
switch and press [ENTER].
≥Audio Mode
L/R, L, R
≥PCM FIX
On: Select when receiving only PCM signals.
Off
:
Select w
hen receiving Dolby Digital and PCM
signals.
≥DRC (Dynamic Range Compression)
On: Adjusts for clarity even when the volume is low by
compressing the range of the lowest sound level
and the highest sound level. Convenient for late
night viewing. (Only works with Dolby Digital)
Off
3 Press [34] to select the setting and press [ENTER].
To return to the previous screen
Press [RETURN].
[Note]
Audio that is input through the OPTICAL IN (TV) terminal
cannot be output through the HDMI terminal.
Setting the Dolby Virtual Speaker
^"""""""""""""""}
[REFERENCE] Standard mode
(factory preset for [DVD-V] only)
v
[WIDE] Wide mode
≥This mode widens the acoustic
field of the front/center speakers.
This has a good effect when there
is little space between the
speakers.
v
[OFF] (factory preset)
DISC SFC
TG
HDMI D.MIX
MONO
SLP
ST
CT
MODE
AC
PRG
RDS
DTS
PL
A
PS
PTY
H.BASS
2
SRD
PGM
HDCD
E.
CD
DVD
W
D
Center Mark
DISC SFC
TG
HDMI D.MIX
MONO
SLP
ST
CT
MODE
AC
PRG
RDS
DTS
PL
A
PS
PTY
H.BASS
2
SRD
PGM
HDCD
E.
CD
DVD
W
D
Setting the sound effects for the cable box,
digital broadcasts or satellite receiver
IN (TV)
OPTICAL
To DIGITAL
OUT
Back of the main unit
Optical digital audio cable (not included)
≥Do not bend sharply when connecting.
DIGITAL IN
Sub Menu
Off
PCM FIX
Off
DRC
L/R
Audio Mode
Convenient functions
Advanced Operations
PTX79P.book Page 83 Monday, April 9, 2007 9:24 AM