Panasonic PT-DZ16KE Home Theater System User Manual


 
Chapter 6Appendix — Technical information
ENGLISH - 169
Mode
Resolution
(Dots)
Scanning freq.
Dot clock
freq.
(MHz)
Format
Plug and play
*1
Horizontal
(kHz)
Vertical
(Hz)
RGB2
DVI-D
HDMI
EDID1 EDID2 EDID3
1280 x 720
1 280 x 720 37.1 49.8 60.5 R/D/H
1 280 x 720 44.8 59.9 74.5 R/D/H
1 280 x 720 76.3 100.0 131.8 R/D/H
1 280 x 720 92.6 120.0 161.6 R/D/H
1280 x 768
1 280 x 768 39.6 49.9 65.3 R/D/H
1 280 x 768 47.8 59.9 79.5 R/D/H
1 280 x 768
*4
47.4 60.0 68.3 R/D/H
1 280 x 768 60.3 74.9 102.3 R/D/H
1 280 x 768 68.6 84.8 117.5 R/D/H
1280 x 800
1 280 x 800 41.3 50.0 68.0 R/D/H
1 280 x 800 49.7 59.8 83.5 R/D/H
1 280 x 800
*4
49.3 59.9 71.0 R/D/H
1 280 x 800 62.8 74.9 106.5 R/D/H
1 280 x 800 71.6 84.9 122.5 R/D/H
MSXGA 1 280 x 960 60.0 60.0 108.0 R/D/H
SXGA
1 280 x 1 024 52.4 50.0 88.0 R/D/H
1 280 x 1 024 64.0 60.0 108.0 R/D/H
1 280 x 1 024 72.3 66.3 125.0 R/D/H
1 280 x 1 024 78.2 72.0 135.1 R/D/H
1 280 x 1 024 80.0 75.0 135.0 R/D/H
l
l l l
1 280 x 1 024 91.1 85.0 157.5 R/D/H
1366 x 768
1 366 x 768 47.7 59.8 85.5 R/D/H
1 366 x 768 39.6 49.9 69.0 R/D/H
SXGA+
1 400 x 1 050 54.1 50.0 99.9 R/D/H
1 400 x 1 050 64.0 60.0 108.0 R/D/H
1 400 x 1 050 65.2 60.0 122.6 R/D/H
l
l l l
1 400 x 1 050 65.3 60.0 121.8 R/D/H
1 400 x 1 050 78.8 72.0 149.3 R/D/H
1 400 x 1 050 82.2 75.0 155.9 R/D/H
WXGA+
1 440 x 900 55.9 59.9 106.5 R/D/H
1 440 x 900 46.3 49.9 86.8 R/D/H
1600 x 900
1 600 x 900 46.4 49.9 96.5 R/D/H
1 600 x 900 55.9 60.0 119.0 R/D/H
l
l l l
UXGA60 1 600 x 1 200 75.0 60.0 162.0 R/D/H
l
l l l
WSXGA+
1 680 x 1 050 65.3 60.0 146.3 R/D/H
1 680 x 1 050 54.1 50.0 119.5 R/D/H
1920 x 1080
1 920 x 1 080 55.6 49.9 141.5 R/D/H
1
920 x 1 080
*4
66.6 59.9 138.5 R/D/H
1 920 x 1 080
*5
67.2 60.0 173.0 R
WUXGA
1 920 x 1 200 61.8 49.9 158.3 R/D/H
1 920 x 1 200
*4
74.0 60.0 154.0 R/D/H
l
l
1 920 x 1 200
*5
74.6 59.9 193.3 R
*1 Signals with a l in the Plug and play columns are signals described in EDID (extended display identication data) of the projector. If a signal has no
l in the Plug and play columns but has an entry in the Format column, it can be input. For signals without a l in the Plug and play columns, there
are instances when resolution cannot be selected on the computer even though the projector supports them.
*2 Pixel-Repetition signal (dot clock frequency 27.0 MHz) only
*3 When a 1125 (1035)/60i signal was input, it is displayed as a 1125 (1080)/60i signal.
*4 VESA CVT-RB (Reduced Blanking)-compliant
*5 Samples the pixels in the image processing circuit and projects the image.
Note
f The number of display dots for the PT-DZ16K series is 1 920 x 1 080. A signal with a different resolution is converted to the number of
display dots.
f The “i” at the end of the resolution indicates an interlaced signal.
f When interlaced signals are connected, ickering may occur on the projected image.