Filter
Top Products
15
Connections
7. Connecting a DVD recorder or other digital video
recording device (VIDEO 1)
If the device is equipped with an S video output terminal, connect it
to the S VIDEO 1 IN terminal with an S video cable. If it does not
have an S video output terminal, connect its video output terminal to
the VIDEO 1 IN terminal using an RCA-type video connection
cable. You do not need to connect to both the S VIDEO 1 IN and
VIDEO 1 IN terminals. If the device has component video outputs,
connect them to one of the COMPONENT VIDEO INPUT jacks.
With the initial settings of the DTR-6.2, the VIDEO 1 input
source is set for the COMPONENT VIDEO INPUT 2 jack.
If the video connection is made at COMPONENT VIDEO INPUT 1,
this must be changed at the Setup menu: Input Setup → Video Setup
→ Component Video (see pages 26, 38).
Using an RCA-type audio connection cable, connect the audio
output terminal on the device to the same VIDEO 1 IN audio jacks
on the DTR-6.2 and audio input terminal to the VIDEO 1 OUT audio
jacks. Make sure that you properly connect the left channel to the L
jack and the right channel to the R jack.
If the device has a digital output jack as well, be sure to also connect
it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT
(OPTICAL) jack on the DTR-6.2 depending on the type of
connector on the device.
With the initial settings of the DTR-6.2, the VIDEO 1 input
source is set for digital input at the COAXIAL 2 jack.
If the digital connection is made at a different jack, this must be
changed at the Setup menu: Input Setup → Audio Setup → Digital
Input (see pages 26, 38).
8. Connecting a television monitor or projector
(MONITOR OUT)
The DTR-6.2 is equipped with a simple Y/C separate circuit and
simple Y/C mixed circuit. Since both the signal from the S VIDEO
and VIDEO inputs are output to the MONITOR OUT S VIDEO
output, if the television or projector is equipped with an S video
input, it is unnecessary to connect the video connectors. If it is
equipped with only a video input, connect it to the MONITOR OUT
VIDEO output.
If the monitor or projector is equipped with an S video output
terminal, connect it to the MONITOR OUT S VIDEO terminal with
an S video cable. If it does not have an S video output terminal,
connect its video output terminal to the MONITOR OUT VIDEO
terminal using an RCA-type video connection cable. You do not
need to connect to both the MONITOR OUT S VIDEO and
MONITOR OUT VIDEO terminals. If the device has component
video inputs, connect them to the COMPONENT VIDEO OUTPUT
jacks.
Caution:
Note that the Setup menu will only be displayed on the monitor
connected to MONITOR OUT and not those connected to the
COMPONENT VIDEO OUTPUT jacks.
9. Connecting settop box or video camera, etc.
(VIDEO 4)
If the device is equipped with an S video output terminal, connect it
to the S VIDEO 4 IN terminal with an S video cable. If it does not
have an S video output terminal, connect its video output terminal to
the VIDEO 4 IN terminal using an RCA-type video connection
cable. You do not need to connect to both the S VIDEO 4 IN and
VIDEO 4 IN terminals.
If the video connection is made at COMPONENT VIDEO INPUT 2,
this must be changed at the Setup menu: Input Setup → Video Setup
→ Component Video (see pages 26, 38).
Using an RCA-type audio connection cable, connect the audio
output terminal on the device to the audio DVD IN jacks on the
DTR-6.2. Make sure that you properly connect the left channel to the
L jack and the right channel to the R jack.
If the device has a digital output jack as well, be sure to also connect
it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT
(OPTICAL) jack on the DTR-6.2 depending on the type of
connector on the DVD player.
With the initial settings of the DTR-6.2, the DVD input source is
set for digital input at the COAXIAL 1 jack.
If the digital connection is made at a different jack, this must be
changed at the Setup menu: Input Setup → Audio Setup → Digital
Input (see pages 26, 38).
5. Connecting a video cassette recorder (VIDEO 2)
If the video cassette recorder is equipped with an S video output
terminal, connect it to the S VIDEO 2 IN terminal with an S video
cable. If it does not have an S video output terminal, connect its
video output terminal to the VIDEO 2 IN terminal using an RCA-
type video connection cable. You do not need to connect to both the
S VIDEO 2 IN and VIDEO 2 IN terminals. If the video cassette
recorder has component video outputs, connect them to one of the
COMPONENT VIDEO INPUT jacks.
With the initial settings of the DTR-6.2, the VIDEO 2 input
source is set for the COMPONENT VIDEO INPUT 1 jack.
If the video connection is made at COMPONENT VIDEO INPUT 2,
this must be changed at the Setup menu: Input Setup → Video Setup
→ Component Video (see pages 26, 38).
Using an RCA-type audio connection cable, connect the audio
output terminal on the video cassette recorder to the same VIDEO 2
IN audio jacks on the DTR-6.2 and audio input terminal to the
VIDEO 2 OUT audio jacks. Make sure that you properly connect the
left channel to the L jack and the right channel to the R jack.
6. Connecting a satellite tuner or television (VIDEO 3)
If the satellite tuner or television is equipped with an S video output
terminal, connect it to the S VIDEO 3 IN terminal with an S video
cable. If it does not have an S video output terminal, connect its
video output terminal to the VIDEO 3 IN terminal using an RCA-
type video connection cable. You do not need to connect to both the
S VIDEO 3 IN and VIDEO 3 IN terminals. If the satellite tuner or
television has component video outputs, connect them to one of the
COMPONENT VIDEO INPUT jacks.
With the initial settings of the DTR-6.2, the VIDEO 3 input
source is set for the COMPONENT VIDEO INPUT 1 jack.
If the video connection is made at COMPONENT VIDEO INPUT
2, this must be changed at the Setup menu: Input Setup → Video
Setup → Component Video (see pages 26, 38).
Using an RCA-type audio connection cable, connect the audio
output terminal on the satellite tuner or television to the same
VIDEO 3 IN audio jacks on the DTR-6.2. Make sure that you
properly connect the left channel to the L jack and the right channel
to the R jack.
If the satellite tuner or television has a digital output jack as well, be
sure to also connect it to either a DIGITAL INPUT (COAXIAL) or
DIGITAL INPUT (OPTICAL) jack on the DTR-6.2 depending on
the type of connector on the set top box or television.
With the initial settings of the DTR-6.2, the VIDEO 3 input
source is set for digital input at the OPTICAL 2 jack.
If the digital connection is made at a different jack, this must be
changed at the Setup menu: Input Setup → Audio Setup → Digital
Input (see pages 26, 38).