Filter
Top Products
12
Default setting
Input source Digital input Component video Multichannel
DVD COAX 1 INPUT 1 Yes
Video 1 COAX 2 INPUT 2 No
Video 2 ---- INPUT 1 No
Video 3 OPT 2 INPUT 1 No
Video 4 ---- INPUT 1 No
Tape ---- No
FM
AM
Phono ---- No
CD OPT 1 No
IN
OUT
6 OHMS
MIN.
/
SPEAKER
R
L
P
B
P
R
Y
REMOTE
CONTROL
INPUT 1
INPUT 2OUTPUT
AC
OUTLETS
AC 120
V 60
Hz
SWITCHED
TOTAL 120
W
1
A MAX.
FM
75
AM
ANTENNA
GND
P
B
P
R
Y
P
B
P
R
Y
COMPONENT
VIDEO
4 OHMS
MIN.
/
SPEAKER
FRONT
SPEAKERS
CENTER
SPEAKER
SURROUND
SPEAKERS
ZONE 2
SPEAKERS
R
L
R
L
R
L
FRONT SURR
L
R
1
2
PRE
OUT
CENTER
L
R
VIDEO
1
VIDEO
2
DVD
VIDEO
4
IN
OUT
IN
OUT
IN
IN
IN
MONITOR
OUT
VIDEO
3
L
R
CENTER
SUB
WOOFER
FRONT
SURR
SUBWOOFER
OPTICAL
COAXIAL
1
2
12
PRE OUT
MULTI
CHANNEL INPUT
DIGITAL
INPUT
L
R
OUT
IN
PHONO
TAPE
CD
IMPEDANCE SELECTOR
SET BEFORE POWER ON
ZONE 2
PRE OUT
IN
OUT
IR
RS
232
A
B
12 V
TRIGGER
AC INLET
AV RECEIVER
MODEL NO. DTR-6.2
CAUTION
:
SEE INSTRUCTION MANUAL
FOR CORRECT SETTING.
VIDEO
S
VIDEO
DVD
VIDEO
4
VIDEO
3
Connections
Here is explanation of how to connect the main components to the
DTR-6.2 in the standard manner. There are many ways that any one
component can be connected, and it is up to you to decide which
method best fits your situation. The directions given here are only
one option and should only be thought of as such. It is best to fully
understand the nature of each connector and terminal as well as each
of your components and their features to ascertain which method of
connection is best.
• Be sure to always refer to the instructions that came with the
component that you are connecting.
• Do not plug in the power cord until all connections have been
made.
• For input jacks, red connectors (marked R) are used for the
right channel, white connectors (marked L) are used for the
left channel, and yellow connectors (marked V) are used for
video connection.
• Do not bind audio/video connection cables with power cords
and speaker cables. Doing so may adversely affect the
picture and sound quality.
• When using the digital inputs, make sure to also connect the
analog connections whenever possible.
• When using one of the optical input jacks, remove the
protective cap and keep it safely. When the jack is not
used, replace the protective cap.
• When using an optical input jack, always use an optical
fiber cable.
Improper connection
Inserted completely
Optical digital input terminal
An optical digital input terminal is equipped
with a protection cap. When connecting,
remove this cap. When not using, put the
cap back on the terminal.
COAX: Coaxial OPT: Optical ----: No setting : Not applicable
Connecting the remote
zone speakers [19]
Connecting power amplifiers [16]
Connect to devices with
multichannel output [17]
Connecting a
subwoofer [18]
Connecting your
audio components
[13]
Connecting antennas [22, 23]
Connect to devices with z
terminals [16]
Connecting your video
components [14, 15]
Connecting speakers [17-19]
Cautions regarding the AC
OUTLETS connectors [16]
• Insert all plugs and connectors securely. Improper
connections can result in noise, poor performance, or
damage to the equipment.
RS232 port [17]
Operating components
not reached by the remote
controller signals [20]
Plugging in the power cord to
the AC INLET receptacle [17]
12V TRIGGER A, B terminals
[17]