Filter
Top Products
228
Settings Common to All Modes (System Function)
MTC Offset Time Hour
Coordinates the playback timing of the Fantom-X and the external
device in an hour units.
Value:
00–23 hours
MTC Offset Time Minute
Coordinates the playback timing of the Fantom-X and the external
device in a minute units.
Value:
00–59 minutes
MTC Offset Time Second
Coordinates the playback timing of the Fantom-X and the external
device in a second units.
Value:
00–59 seconds
MTC Offset Time Frame
Coordinates the playback timing of the Fantom-X and the external
device in a frame units.
Value:
00–29 frames
MTC Error Level
Determines how often the reception status is checked when MTC is
being received from an external device. Stop synchronization if a
problem becomes apparent with the check.
Value:
0–10 (the checking interval will be longer for larger values)
In strict terms, the lower the numerical value set, the more
accurate the check is. However, playback may be stopped
overly frequently if too rigorous a check is made, and this soon
becomes inconvenient. By raising the Error Level setting, then
even if problems with the reception of MTC do occur,
synchronization can then continue as long as such problems
remain at a level that does not cause undue problems.
Metronome Mode
Specifies when you want the metronome to sound.
* If [F7 (Click)] in the Tempo window which appears when you press
[TEMPO] is lit in red, the metronome will always sound.
Value
OFF:
Will not sound.
PLAY ONLY:
Will sound only during playback.
REC ONLY:
Metronome will sound only for recording.
PLAY&REC:
Metronome will sound for playback and recording.
ALWAYS:
Metronome will always sound.
Metronome Level
You can adjust the volume of the metronome.
Value:
0–10
Metronome Sound
Selects the metronome sound.
Value
TYPE 1:
A conventional metronome sound will be heard. A
bell will sound on the first beat.
TYPE 2:
Clicks will sound.
TYPE 3:
Beeps will sound.
TYPE 4:
Cowbell will sound.
Beat Indicator Mode
You can specify how the beat indicator on the panel will blink.
Value
ALWAYS (always blinks at the specified tempo)
PLAY&REC (blinks only during playback and recording)
Types of MTC
The types of MTC that can be selected by the Fantom-X are
shown below. Select the same frame rate as that set for the
external device. When not using a video device, then any frame
rate may be selected as long as the rates are the same on both
devices being synchronized.
30: This is 30 frames per second, non-drop format. This is
used by audio devices such as analog tape recorders,
and for NTSC format black and white video (used in
Japan and the U.S.).
29N: This is 29.97 frames per second, non-drop format. This
is used for NTSC format color video (used in Japan and
the U.S.).
29D: 29.97 frames per second drop format. This is used for
NTSC format color video (used in Japan and the U.S.).
25: 25 frame per second frame rate. This is used for SECAM
or PAL format video, audio equipment, and film (used
in Europe and elsewhere).
24: 24 frame per second frame rate. This is used for video,
audio devices, and film in the US.
Non-Drop Format and Drop Format
There are two types of format used by NTSC video cassette
recorders, non-drop and drop. Non-drop format features
continuous time code, whereas in drop format, which is used
for NTSC color video format, the first two frames of every
minute are dropped, except for those at ten-minute intervals. In
most video and audio production, since formats with
continuous frames are easier to deal with, non-drop is generally
used. In contrast, in situations such as in broadcast, where the
time code must match actual clock time, drop is used.
Metronome
Fantom-X678_r_e.book 228 ページ ２００５年５月１２日 木曜日 午後４時４０分