Filter
Top Products
25
KRF-V7771D (En/T)
Setup
Operation in the “10key Pad (Macro) “screen.
Operation in the “Custom 1 Edit: VCR” screen.
4
5
Check the operation after setting the time. If macro play does
not occur, increase the time settings with the following proce-
dure.
1 Set the “Pwr” (Power) on time.
Select with the
or icon of “Pwr”.
÷ Select the “Pwr” icon to test the operation.
2 Set the “Ply” (Play) start time.
Select with the
or icon of “Ply”.
÷ Select the “Ply” icon to test the operation.
3 Set the “Input Select” code output timing of the VCR.
Select with the
or icon of “Input Select”.
÷ Select the “Input Select” icon to test the operation.
4 Open the “10key Pad” menu screen to select a channel.
Select “Channel” icon.
÷ Set as described in step
5.
5 Set the “Channel Code” output timing of the VCR.
Select with the
or icon of “Channel Code”.
÷ Select the “Channel Code” icon to test the operation.
6
Perform selection in the “Macro Edit: Custom 1, 2 or 3” menu screen.
Check the operation after setting the time. If macro play does
not occur, increase the time settings with the following proce-
dure.
1 Set the “Pwr” (power) ON time.
Select with the
or icon.
÷ Select the “Pwr” icon to test the operation.
2 Select whether “TV1” or “TV2” is to be controlled.
3 Set the “Video Select” code output timing.
Select with the
or icon.
÷ Select the “Video Select” icon to test the operation.
4 Set the “TV Select” code output timing.
Select with the
or icon.
÷ Select the “TV Select” icon to test the operation.
1 Select the “Channel” icon in step 4 to open the “10key Pad
(Macro)” menu screen.
2 Set a channel.
(Example)
To set CH 11 : Select the +10, and then 1 icons.
÷ The way to input channel differs depending on manufacturers.
Refer also to the manual of your connected components.
3 Select the
icon to establish the selection.
When
is selected, the screen returns to the previous
menu.
÷ To output a set channel code, select the “Channel Code” icon in
step
4.
÷ The output timing of each code can be switched as shown below.
= - - += 0s (second) += 1s += 2s +=
.......
+=
15s +
“- -” indicates that no code is output, and “0s” indicates that the
code is output at the same time as a macro execute icon is
selected.
÷ The component name after “Edit:
.......
” is switched to “VCR”,
“Cable”, “Satellite”, “LD”, “DVD”, “CD”, “MD” or “Tape”
according to the selected input.
Setup for macro play (automatic operation)
Clr :Select to clear all the input “ ”
Entr : Select when it is required to enter a value selection.
>12 :Select when inputting a channel value of 13 or more.
-/-- : Select to switch between the 1-digit input or 2-digit
input.
Pwr :Setting of the TV’s “Pwr” code output timing.
TV :Selection of the controlled TV from “TV1” and
“TV2”.
Video Select :Selection of the TV’s “Video Select” code output
timing.
TV Select :Selection of the TV’s “TV Select” code output
timing.
If the “Device” icon is selected in step 3, the menu screen
below appears.
If the “TV” icon is selected in step 3, the menu screen
below appears.
Custom 1 Edit:VCR
Channel
Pwr Pl
y
Channel Code
In
p
ut Select
0s
1s
1s
0s
2
1
4
3
5
10ke
y
Pad
(
Macro
)
1
2
3
6
7
8
10 11 12
9
0
4
5
+10
Clr
Entr
>12
-
/
-
-
+100
Number of icon
input
(10 digits max.)
2
3
Custom 1 Edit:TV
Pwr TV
TV Select
Video Select
0s
1s
1s
TV2
2
1
3
4