Filter
Top Products
60
Chapter 3 Recording Your Performance (Sequencer)
Settings for the Pattern
fig.3-08.e
1 – 999
0 – 127
SETUP
PART
Time Sig.
Inst
Specifying the Time Signature
Specifying the Length (Number of Measures) of the Pattern
Specifying the Time to Return the Pattern to the Beginning
Ignoring a pause at the beginning of the pattern
Specifying the Tempo of the Pattern
Choosing a Playing Method
Selecting the Instrument of the Part
Adjusting the Volume of the Part
Length
Reset Time
Quick Play
Tempo
PlayType
Level
Loop, OneShot,
Tap, TapVelo
OFF, ON
20 – 240, (MIDI)
OFF, 0.1 – 4.0s
Numerator:
1 – 13
Denominator:
2, 4, 8, 16
Pan
Adjusting the Pan (Localization) of the Part
TransposeMl1
TransposeMl2
Bend Range
Adjusting the Amount of Change in Pitch
Adjusting the Pitch of Melody Parts
L63 – Center – R63
-24 – +24
0 – 24
Reverb Send
Adjusting the Depth of Reverb Applied to the Part
(when the effect is off)
MULTI-FX/LFO
Turning the Multi-Effects On/Off for the Part
0 – 127
OFF, ON
PadNote
Specifying the Note of Each Pad
C-1 – G9
MELO1,
MELO2
PERC1,
PERC2
0 – 127
(Patch)
Selecting the Patch Played by the Part
Adjusting the Volume of the Part
Level
Reverb Send
Adjusting the Depth of Reverb Applied to the Part
(when the effect is off)
MULTI-FX/LFO
Turning the Multi-Effects On/Off for the Part
0 – 127
OFF, ON
When "Ext" is selected for the Seq Sync (p. 68), "MIDI" ( =MID) will appear.
Loop: After the pattern is played back to the end, playback then repeats
and continues until [PLAY/STOP] is pressed.
In Tap playback, this returns the pattern to the beginning if the set time
interval elapses without the pad being hit again. If it is set to "OFF," this
function will be disabled.
If "ON" is selected, this starts playback of the pattern from the
first note even if a pause is left at the beginning of the pattern.
This transposes the key of the melody parts in semitone steps.
This adjusts the amount of change in pitch with pitch bend
at maximum level in semitone steps.
You can use the pads to record patterns if you have no MIDI keyboards.
This parameter specifies the note of each pad in this case. Strike (Sound)
the pad (D Beam, ribbon) to select it that you wish to specify the note.
Select
Selecting the Part
Perc1, Perc2,
Melo1, Melo2
1 – 54 (refer to p. 94)
Category Parameter Value
Numerator: Number of beats per measure
Denominator: Basic note value
* It is not possible to change while the pattern is playing back.
* The same type of the effect which is selected in Play mode will be selected.
It is different from the type which is set in the patch selected for the Part.
* You can use the pads to sound the tone of the part in the part screen.
* It is not possible to change while the pattern is playing back.
TapVelo: Tap playback with changes of the volume depending on how strongly
the pad are struck.
Tap: Each time the [PLAY/STOP] is pressed (or pad is struck; refer to p. 54),
the sounds contained in a pattern are played back one at a time in sequence.
OneShot: Playback stops once the end of the pattern is reached.
When "Replace" is selected for the RecMode (p. 62), it is not necessary to specify
the Length. Recording will continue until you press [PLAY/STOP], and the number
of measures recorded will automatically become the "Length" setting.
Ml1: Melody Part 1, Ml2: Melody Part 2
* It is not possible to change after the pattern is recorded.