Filter
Top Products
108
<PRE1269>
En/Fr
Record the source through analog input or record copy-
permitted music.
Check if the digital input cable is not disconnected and if the
power of the source player is on.
Check whether the source is a regular music source.
Stop playing the source player.
In a while, "1-SYNC" or "AL-SYNC" is displayed, and the unit
is set to the synchro recording standby mode.
Wait until these messages disappear.
While "REPAIR" is displayed, the track number and recording
time data are repaired by tracking the recorded area. Further
recording or finalization is possible whenever the display
returns to the previous condition.
Tracing of the recorded area takes about 40 minutes if the
disc has been recorded fully.
Replace the disc with a new one.
Erase a CD-RW disc.
Load a CD-R or CD-RW disc with “FOR CONSUMER”
indication.
Take out and check the disc.
Digital musical signal containing copy
inhibit signal based on SCMS is being
input.
The digital input is interrupted.
The data (CD-ROM, etc.) provided cannot
be recorded.
The source player was already playing
when the DIGITAL SYNCHRO button
was pressed.
The unit is making preparations for
recording.
Because the disc was left in the unit
after recording and the power plug was
unplugged later, the track number and
recording time data have been cleared
without being recorded on the disc.
No more recording is possible because
the available recording time of the disc
has been used fully or 99 tracks have
already been recorded on the disc.
The loaded disc is a CD-R or CD-RW disc
for professional use without “FOR
CONSUMER” indication.
A blank disc is loaded.
An attempt is made to play a blank disc.
An attempt is made to start playback
without loading a disc.
The unit is resuming an operation. After
the power supply is cut off by a power
failure or by mistake during recording,
the unit enters RESUME mode so that
additional recording is possible.
“NEW DISC”
“NO DISC”
“RESUME”
The loaded disc is a blank CD-R or CD-RW disc. Recording is
possible but playback is not.
Open the tray and check if a disc is loaded.
Wait until the message disappears.
In case of trouble, first check the following list. What seems to be a failure of the unit is sometimes due to imperfect
maintenance, defective disc or unaccustomed operation. Such troubles are often recovered by correcting simple mistake or
misunderstanding or by simple maintenance operation. If your trouble cannot be recovered after checking the following list,
please call you nearest PIONEER service center or station.
Self-diagnostics
This unit incorporates a self-diagnostic function.
When it detects trouble during an operation, it displays one of the following messages on the display panel.
The disc is stopped due to dirt, stain,
scratch or vibration.
The disc may be loaded upside down.
A system error occurred perhaps due to
noise or static electricity.
Take out the disc and check for dirt, dust, scratch, etc.
Take out and check the disc.
If the same messages are displayed again after the disc is
reloaded, unplug the power cord and plug it in again.
If the same messages are displayed again, please contact a
PIONEER authorized service center.
Unplug the power cord and plug it in again.
If the same messages are displayed again, please contact a
PIONEER authorized service center.
Alternate display of
"CHECK and "DISC"
page 18
page 38
Display Cause
Treatment Ref. Page
Display blinks
"CHECK"
CauseDisplay
Treatment
Ref. page
Information messages related to recording operation
Alternate display of
"CAN NOT" and
"COPY".
Alternate display of
"CAN NOT" and
"REC".
Cyclic display of
"CHECK", "INPUT"
and "CD ?".
Alternate display of
"SET" and "UP".
"REPAIR"
"REC FULL"
"Pro DISC"
page 58
page 20
page 62
page 44
page 48
page 50
page 42
page 78
page 14, 42
CauseDisplay
Treatment
Ref. page
Information messages related to playback operation
page 16
page 38
page 38
page 62
page 76
TROUBLESHOOTING
En