Filter
Top Products
Programming the Remote
Example: One blink, followed by a one-second
pause, followed by six blinks, followed by a one-
second pause, followed by four blinks indicates
that the code has been set to 164.
For future reference enter the Setup Codes for
t
he equipment in your system here:
DVD ____________ CD ________________
VID1/VCR ________VID3/TV __________
V
ID2/CBL/SAT ______________________
TAPE ______________________________
VID4 ______________________________
Learning Codes from a Remote
(AVR 355 Remote only)
In addition to using codes from the remote’s
internal code library, theAVR 355’s remote is
able to “learn” codes from remotes that may not
be in the code library. In addition, you may use
this function to “learn over” the codes from a
preprogrammed device to add functions not
included in the preprogrammed codes.To learn
or transfer codes from an IR remote to the
AVR 355’s remote, follow these steps:
1. Place the front of the original remote with the
code being sent so that it is facing the IR
Transmitter Window
w
on the AVR 355
remote “head-to-head.”The remotes should be
between 2 and 4 cm apart.
2. Select the button on the remote that you wish
to use as the device selector for the codes about
to be entered.This must be any of the Input
Selectors
4
or the AVR Selector
5
. Note
that when new codes are learned with the AVR
Selector
5
, they may no longer control the
AVR 355.
3. Press the Input Selector
cy
button
under which you wish to learn one or more but-
tons. Now press the Learn Button (T) for 3 sec-
onds. The Input Button that you pressed last
lights up. It is important that you begin the next
step within 25 seconds.
4. Press the button on theAVR 355 remote that
you wish to program. Note that the Input Button
blinks once.
Important Note: The following buttons are
learnable: DEVICE POWER ON/OFF, 0~9,LAST,
BACK/EXIT, MENU, UP,DOWN, LEFT, RIGHT, OK,
DISC MENU, RED, GREEN,YELLOW, BLUE,
CHANNEL UP/DOWN,VOLUME UP/DOWN,
MUTE, PREVIOUS, NEXT, FF, REW, PLAY,STOP,
RECORD (Total 37 keys).These buttons can be
p
rogrammed differently in each DEVICE mode. If
you try to select a non-learnable button, the
Input Button blinks rapidly.
5. Place the two remotes facing each other at 2-
4
cm distance. Now press and hold the button on
the original remote that you wish to“teach”
into the AVR 355 remote.When the Input Button
on the AVR 355 blinks 3 times, the code has
been learned.
6. Repeat steps 4 though 5 for each button on
the source remote that you wish to transfer to
the AVR 355 remote.
7. Once all codes have been transferred from the
original source remote to theAVR 355 remote,
press the Learn button
t
.The Input Button
blinks 3 times and the light extinguishes to indi-
cate that Learn mode is turned off.
8. Repeat Steps 1 through 7 for any additional
remotes you wish to “teach” into theAVR 355
Remote.
Erasing Learned Codes
TheAVR 355’s remote allows you to remove or
erase the code learned into a single button for a
single device, to remove or erase all the codes
that have been learned for a single device, or to
erase all commands that have been learned to all
devices.
To erase a single learned code from
within a single device’s settings, follow
these steps:
1.Press and release the Input Selector
cy
within which the individual button to be erased
has been programmed.
2.Press the Learn Button
t
for 3 seconds.The
Input Button pressed before lights up.
3.Press and release the Input Selector
cy
again for the device within which the individual
b
utton to be erased has been programmed.
4.Press the 7 button
k
three times.
5
. Press and release the individual button for
which the code is to be erased.The Input Button
selected blinks 3 times.
6.To erase other buttons within the same device,
press them as noted in Step 5.
7.Press the Learn Button
t
for 3 seconds.The
Input Button pressed before lights up.
To erase all codes within a single device,
follow these steps:
1.Press and release the Input Selector
cy
for which you wish to erase the codes.
2.When the red LED under the Input Selector
turns red and the Program/SPL Indicator
2
flashes amber, release the buttons.
3.Press and release the same Input Selector
cy
again for the device whose codes you wish
to erase.
4.Press the 8 button
k
three times.
5.Input Button selected blinks 3 times and extin-
guishes.
To erase all codes that have been pro-
grammed to all devices in the remote,
follow these steps:
1.Press the Learn button
t
for 3 seconds.
2.Press and release any Input Selector button
cy
.
3.Press the 9 button
k
three times.
4.The Input Button selected blinks 3 times and
extinguishes.All buttons in all modes are now
reset to the original code set.
ENGLISH
PROGRAMMING THE REMOTE 43