Filter
Top Products
The Surround Setup menu
06
59
En
7 If you selected ‘Reverb View’, you can use the
cursor buttons (hard keys) to check the reverb
characteristics for each channel. Select ‘Return’ and
press ENTER when you’re done.
Use the / (cursor left/right) buttons to select the
channel and the frequency you want to check. Use the
/ (cursor up/down) buttons to go back and forth
between the two. Note that the markers on the vertical
axis indicate decibels in 2dB steps.
8 If you selected ‘Advanced EQ Setup’, input the
time setting you want to use for calibration, then
select ‘Go’. Select ‘Start’ from the next screen.
Based on the reverb measurement above, you can
manually choose the time period that will be used for the
final frequency adjustment and calibration. Even though
you can make this setting without reverb measurement,
it is best to use the measurement results as a reference
for your time setting. For an optimal system calibration
based on the direct sound coming from the speakers, we
recommend using the 20–40ms setting.
Use the / (cursor left/right) buttons to select the
channel, frequency, and time setting. Use the /
(cursor up/down) buttons to switch between them.
You can switch between your connected speakers
(excluding the subwoofer), and display the
measurements for the following frequencies: 63Hz, 125
Hz, 250Hz, 500Hz, 1kHz, 2kHz, 4kHz, 8kHz and 16kHz.
Select the setting from the following time periods (in
milliseconds): 0–20ms, 10–30ms, 20–40ms, 30–50ms,
40–60ms, 50–70ms and 60–80ms. This setting will be
applied to all channels during calibration.
When you’re finished, select Go. It will take about 2–11
minutes for the calibration to finish.
!! Complete !! is displayed on-screen after the acoustic
calibration equalization is set. If you want to check the
settings, select Check and press ENTER. If you want to
finish, select Return to exit each screen.
X-Curve
Most soundtracks mixed for cinema sound too bright
when played back in large rooms. The X-Curve setting
acts as a kind of re-equalization for home theater
listening, and restores proper tonal balance of movie
soundtracks.
1 Select ‘X-Curve’ then press ENTER.
2 Use the / (cursor left/right) hard keys to
switch the X-Curve ON or OFF.
If you select OFF, the frequency curve will be flat and you
won’t be able to adjust the X-Curve.
3 Select a setup option and press ENTER.
• Manual – Adjust the X-Curve manually.
• Semi Auto – The X-Curve is calculated automatically.
The larger your listening area (as determined by the
speaker distance setting), the greater the X-Curve
slope (see the following step for more on this).
4 Check the X-Curve setting. If you selected
‘Manual’, make any adjustments necessary to the X-
Curve.
dB
080160ms
2.4. Acoustic Cal EQ Pro.
Reverb View
[ C ]
[ 500Hz ]
[Return]
dB
080160ms
2.4. Acoustic Cal EQ Pro.
[ C ]
[ 500Hz ]
[20~40ms]
[Go]
[Return]
[ Check ]
[ 1. Speaker Systems ]
[ 2. Channel Level ]
[ 3. Speaker Distance ]
[ 4. Acoustic Cal EQ ]
[ 5. X-Curve ]
[ Return ]
2. Surround Setup
ON
2. 5. X-Curve
X-Curve [ ]
[ Manual ]
[ Semi Auto ]
[ Return ]
Your X-Curve
" –0.5dB/oct "
ON
2. 5. X-Curve
X-Curve [ ]
[ Manual ]
[ Semi Auto ]
[ Return ]
Your X-Curve
" –0.5dB/oct "
63
12
25
50
1k
2k
4k
8k
16
2.5. X-Curve Manual
X-Curve
[ –2.0dB/oct ]
[ Return ]