Filter
Top Products
56
ENGLISH
LISTENING TO XM SATELLITE RADIO
SELECTING AN INPUT SOURCE
Before you can listen to XM Satellite Radio, you must
fi rst select the input source on the SR6001.
P.SCAN
T.MODE
+10
HT-EQ
INPUT
EX/ES
VIRTUAL
CS
dts
P.DIRECT
l/
OFF
ON
SET
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
A/D
LIP SYNC/
MEMO
BAND
CL
SOURCE
112233
445566
778899
00
2.
TAPE
REMOTE CONTROLLER
RC5001SR
MD
CDR
CD
DVD
AMP
AUX2
VCR
DSS
TV
BASS
TREBLE
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
AUX1
TUNERTUNER
1.
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR6001
PURE DIRECT HT-EQ
MODE AUTO
M
PURE DIRECT
SURROUND
DSD
POWER ON/STANDBY
DISP MULTI
SLEEP AU
T
1.
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
VOLUME
UP
DOWN
STANDBY
PHONES
READY
INPUT SELECTOR
AV SURROUND RECEIVER SR6001
MultEQ
MENU
PURE DIRECTHT-EQ
7.1CH INPUT
MODE AUTO
MULTI
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
PURE DIRECT
SURROUND
SPEAKER
MULTI
DSD
POWER ON/STANDBY
L
C
R
SL SSR
LFE
DIGITAL
SURROUND
V-OFFDISPMULTI AUTO TUNED STSPKR A B
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR DIRECT
AUTO
DISC 6.1 MTX 6.1 EQ
PCM
AAC
ENTER
2.
(Using the SR6001)
1.
Turn the INPUT SELECTOR knob to select
“TUNER”.
2.
Press the BAND button to select either XM or
DAB.
(Using the remote control unit)
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote.
2.
Press the BAND button to select XM band.
CHECKING THE XM SIGNAL STRENGTH
AND RADIO ID
-
F.DIRECT
PTY
TUNING
PRESET
-
++
ENTER
EXIT
T.TONE
/SET UP
BASS
TREBLE
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
T.DISPT.DISP
1.
1.
Press the T.DISP button 3 times to displayed
Signal Status.
SIGNAL:
• The display changes as shown below according to
the receiving condition.
SIGNAL: ■■■■■■
SIGNAL: STRONG
(Signal strength is good)
SIGNAL: ■■■■
SIGNAL: MARGINAL
(Signal strength is Marginal)
SIGNAL: ■■
SIGNAL: WEAK
(Signal strength is poor)
XM NO SIGNAL
SIGNAL: NON
(Loss of the signal)
2.
Adjust the antenna location until signal strength
is good.
3.
Select channel 0 (XM000) with the 3 or 4
cursor buttons of the SR6001 or the Q or
R buttons of the remote control unit.
-
T.DISP
F.DIRECT
PTY
TUNING
PRESET
-
++
REMOTE CONTROLLER
TAPE
MENU
ENTER
EXIT
INFO
T.TONE
/SET UP
BASS
TREBLE
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
MD
CDR
CD
AMP
AUX2
TUNER
AUX1
DVD VCR
DSS
TV
3.
R
6001
MultEQ
ENTER
MENU
PURE DIRECT HT-EQ
7.1CH INPUT
MODE AUTO
MULTI
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
PURE DIRECT
SURROUND
SPEAKER
MULTI
DSD
L
C
R
SL SSR
LFE
DIGITAL
SURROUND
V-OFFDISP MULTIAUT O TUNED STSPKR A B
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR DIRECT
AUTO
DISC 6.1 MTX 6.1 EQ
PCM
AAC
3.
• The Radio ID is displayed.
XMOOORADIO ID
Note:
•
If “ANTENNA” appears in the front panel display,
the XM Mini-Tuner and Home Dock may not be
connected to the XM terminal on the rear panel of
this unit properly.
• The ATT function is also effective when XM is
selected.
SWITCHING XM INFORMATION IN THE FRONT
PANEL DISPLAY
You can display XM information (such as artist name/
song title, category or signal status) for the channel
currently selected in the front panel display.
-
F.DIRECT
PTY
TUNING
PRESET
-
++
ENTER
EXIT
T.TONE
/SET UP
BASS
TREBLE
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
T.DISPT.DISP
1.
1.
Press the T.DISP button to displayed
Artist name/Song title
Channel category
Channel number/name
Signal Status
When the Channel number/name mode is displayed:
XMO40:DeepTrc
40:DeepTracks
(If text is more than 13 characters long, the text is
scrolled.)
Note:
The front Panel display can indicate up to 13 alphanumeric
characters at once. If the information contains more then
13 characters, the information scrolls from right to left.