Filter
Top Products
44
ENGLISH
ADJUSTING THE MAIN VOLUME
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
VOLUME
UP
DOWN
MultEQ A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
L
C
R
SL S SR
LFE
DIGITAL
SURROUND
G
HT
E
AK ANALOG
DIGITAL
ATT
EQ
PCM
AAC
READY
CAT
CAT
0
+10
HT-EQ
MULTI/
MENU
SPKR A/B
ENTER
INFO
CH/
M-SPKR
MUTE
7.1CH IN
A/D
MEMO
CL
VOLU MEVOL UME
Adjust the volume to a comfortable level using
the VOLUME control knob on the front panel or
VOLUME + / – buttons on the remote.
To increase the volume, turn the VOLUME knob
clockwise or press VOLUME + button on the remote,
to decrease the volume, turn counterclockwise or
press VOLUME – button on the remote.
Notes:
• The volume can be adjusted within the range of – ∞
to 18 dB, in steps of 1 dB.
•
However, when the channel level is set as described on
page 37, if the volume for any channel is set at +1 dB
or greater, the volume cannot be adjusted up to 18 dB.
(In this case the maximum volume adjustment range
is “18 dB - Maximum value of channel level)
NIGHT MODE
P.SCAN
CAT
T.MODE
123
456
789
0
+10
HT-EQ
SPKR A/B
CH/
INPUT
MUTE
EX/ES
VIRTUAL
CS
VOLUME
dts
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
A/D
LIP SYNC/
MEMO
CL
BAND
(Using the remote control unit)
Press the
NIGHT
button to turn on the Night mode.
Setting the Night mode to “ON” compresses the
dynamic range in Dolby Digital only.
This softens loud passages such as sudden
explosions, to help prevent disturbing others late at
night.
To turn off the Night mode, Press the NIGHT
button again.
ADJUSTING THE TONE (BASS & TREBLE)
CONTROL
TAPE
-
TUNING
PRESET
-
++
REMOTE CONTROLLER
RC5001SR
MD
CDR
CD
DVD
AMP
AUX2
VCR
TUNER
DSS
TV
AUDI O
ANGLE
SUB TITLE
DISC+
CH-SEL
V-O FF
ATT.
AUX1
BASSBASS
TREBLETREBLE
During a listening session you may wish to adjust the
Bass and Treble Control to suit your listening tastes
or room acoustics.
(Using the remote control unit)
To adjust the bass effect, press BASS+ or BASS–.
To adjust the treble effect, TREBLE+ or TREBLE–.
Notes:
• The tone control function is unavailable for the
Source Direct, Pure Direct, Dolby Headphone,
Dolby Virtual Speaker and 192kHz PCM.
• The tone control function is not available when
ACOUSTIC EQ is used.
DIALOGUE NORMALIZATION MESSAGE
Dialogue Normalization (Dial Norm) is a feature of
Dolby Digital.
When playing back software which has been
encoded in Dolby Digital, sometimes you may see a
brief message on the FL display which will read "D-
NORM" (X being a numeric value).
Dialogue Normalization serves to let you know if the
source material has been recorded at a higher or
lower level than usual. For example, if you see the
following message: "D-NORM + 4 dB" on the FL
display, to keep the overall output level constant just
turn down the volume control by 4 dB. In other words,
the source material that you are listening to has been
recorded 4 dB louder than usual.
If you do not see a message on the FL display, then
no adjustment of the volume control is necessary.
SELECTING THE SURROUND MODE
Example: AUTO SURROUND
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR6001
MENU
PURE DIRECT HT-EQ
7.1CH INPUT
MODE AUTO
MULTI
PURE DIRECT
SURROUND
SPEA
K
MU
L
DSD
POWER ON/STANDBY
DISP MULTIAUT O TUNED
SLEEP
SURR DIRECT
AUTO
1 23
456
P.SCAN
T.MODE
INPUT
EX/ES
VIRTUAL
CS
dts
P.DIRECT
l/
OFF
ON
SET
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
BAND
TAPE
REMOTE CONTROLLER
RC5001SR
MD
CDR
CD
AMP
AUX2
TUNER
AUX1
(Using the SR6001)
To select the Auto surround mode during playback,
press the AUTO button on the front panel.
(Using the remote control unit)
To select the Auto surround mode, press the AMP
button fi rst to enter the AMP mode then press the
AUTO button.
• For surround modes, see “Surround Mode” on
page 46.
• To select a specifi c surround mode, Press the
individual surround mode button on page 9 on the
remote control unit.
BASIC OPERATION
(PLAY BACK)
SELECTING AN INPUT SOURCE
Before you can listen to any input media, you must
fi rst select the input source on the SR6001.
Example : DVD
TAPE
REMOTE CONTROLLER
RC5001SR
MD
CDR
CD
AMP
AUX2
TUNER
BASS
TREBLE
AUDI O
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
AUX1
DVD VCR
DSS
TV
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR6001
MENU
PURE DIRECT HT-EQ
7.1CH INPUT
MODE AUTO
MULTI
PURE DIRECT
SURROUND
SPE
A
MU
L
DSD
POWER ON/STANDBY
DISP MULTIAUT O TUNE
D
SLEEP
SURR DIRECT
AUTO
To select DVD, turn the INPUT SELECTOR knob
on the front panel or press the DVD button on the
remote two times in a row. After you have selected
DVD, simply turn on the DVD player and play the
DVD.
• As the input source is changed, the new input
name will appear momentarily an OSD information
on the video display. The input name will also
appear in the display, on the front-panel.
• If you use the FUNCTION RENAME feature (see
page 30) , the renamed name appears on the
display.
• As the input is changed, the SR6001 will
automatically switch to the digital input, surround
mode, attenuation, and night mode status which
were entered during the confi guration process for
that source.
• When an audio source is selected, the last
video input used remains routed to the VCR &
DSS Outputs and Monitor Output. This permits
simultaneous viewing and listening to different
sources.
• When a video source is selected, the selected
video signal is output from the MONITOR OUT
terminal.