Marantz SR6001 Home Theater System User Manual


 
ENGLISH
18
Caution:
Be sure to use speakers with the specifi ed impedance as
shown on the rear panel of this unit.
To prevent damage to circuitry, do not let the bare
speaker wires touch each other and do not let them
touch any metal part
of this unit.
• Do not touch the
speaker terminals
when the power is
on. It may cause
you to receive an
electric shocks.
• Do not connect more than one speaker cable to one
speaker terminal. Doing so may damage this unit.
Note:
Be sure to connect the positive and negative cables for
the speaker properly. If they are miss-connected, the
signal phase will be reversed and the signal quality will
be corrupted.
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect a
powered subwoofer (power amplifi er built in ).
If your subwoofer is a passive type (power amplifi er
is not built in), connect a monaural power amplifi er to
the PRE OUT SUBWOOFER jack and connect the
subwoofer to the amplifi er.
CONNECTING AUDIO COMPONENTS
FM
(
75
)
GND AM
DC OUT
OUTPUT
COMPONENT
VIDEO
IN OUT
PRE
OUT
SLL
RSR
FLASHER
IN
INPUT 1
(
DVD
)
COAX.
DIGITAL IN
DIGITAL OUT
3
54
21
OUT
R
OUT
L
RS-23
2
OUTPUT
TAPE CD/CD-R
OUTOUTIN
MULTI
R
L
DSS
(
AUX2
)
AUDIO
TV
7.1CH
IN
IN
OPT.
DVD
(
2
)
DSS
(
4
)
TV
(
1
)
VIDEO
OUT
VCR
(
3
)
OUTIN
RC-5MULTI RC
INPUT 1
(
TV
)
INPUT 4
(
DSS
)
IN
SR
VCR
IN
INPUT 3
(
VCR
)
DVD SL
INPUT 2
(
DSS
)
ANTENNA
C
B
/
P
B
C
R
/
P
R
C
R
/
P
R
C
R
/
P
R
C
B
/
P
B
C
B
/
P
B
YYY
DVD
(
2
)
DSS
(
4
)
VCR
(
3
)
TV
(
1
)
MONI. OUT
MONITOR
OUT
SBR
SBL
SBR
SBL
C
SW
SW
C
INPUT 2
(
DVD
)
S-VIDEO
HDMI
Ver1.2
XM
OUT IN
L
R
L
R
DIGITAL
INPUT
DIGITAL
OUTPUT
OUT IN
L
R
L
R
L R
L R
RL RL
R L
R L R L
RL
L R
The output audio signal from the TAPE OUT jack and
the CD/CD RECORDER OUT jack is the same signal
which is currently selected.
Caution:
• Do not connect this unit and other components
to mains power until all connections between
components have been completed.
Notes:
• Insert all plugs and connectors securely. Incomplete
connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is
connected to this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables this will result in
generating a hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 5 digital inputs, 2 coaxial jacks and
3 optical jacks, on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a CD, DVD, or other digital
source components.
There is one digital output coaxial jack and one
optical output jack on the rear panel. These jacks
can be connected to a CD recorder, or a MD deck
inputs, respectively.
Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source’s connected to digital input
jacks.
• Use fi ber optical cables (optical) for DIG-1,2,3
input jacks. Use 75 ohms coaxial cables (for digital
audio or video) for DIG-4, 5 input jacks.
You can designate the input for each digital input/
output jacks according to your component. See
page 29.
CD recorder / MD deck
Tape Deck
Analog Audio
Digital Audio (coaxial)
Digital Audio (optical)
Notes:
• There is no Dolby Digital RF input jack. Use an
external RF demodulator Dolby Digital decoder
when connecting the Dolby Digital RF output jack
of the videodisc player to the digital input jack.
• The digital signal jacks on the SR6001 conform
to the EIA standard. If you use a cable that does
not conform to this standard, the SR6001 may not
function properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks are
output through the corresponding digital and analog
jacks, respectively.