Filter
Top Products
52
ENGLISH
7.1 CH INPUT
The SR6001 is equipped for future expansion
through the use of Multi channel Super Audio CD
multichannel player or DVD-Audio player.
When this is selected, the input signals connected to
the L(front left), R (front right), CENTER, SL (surround
left), SR (surround right) and SBL (surround back left)
and SBR (surround back right) channels of the 7.1
CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround
back speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer) jack.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the Monitor Outputs.
This permits simultaneous viewing with video
sources
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR6001
E
MENU
PURE DIRECT HT-EQ
7.1CH INPUT
MODE AUTO
MULTI
PURE DIRECT
SURROUND
SPEAKER
MULTI
DSD
POWER ON/STANDBY
DISP MULTIAUT O TUNED STSPKR
A
SLEEP
SURR DIRECT
AUTO
DISC 6.1
1. 2.
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
VOLUME
UP
DOWN
MultEQ A/B
DE
MEMORY CLEAR
SPEAKERS
MIC
L
C
R
SL SSR
LFE
DIGITAL
SURROUND
M
READY
4.
TAPE
CAT
P.SCAN
CAT
-
T.DISP
F.DIRECT
PTY
TUNING
PRESET
-
++
789
+10
REMOTE CONTROLLER
RC5001SR
00
HT-EQ
MULTI/
MENU
SPKR A/B
ENTER
EXIT
INFO
CH/
T.TONE
/SET UP
M-SPKR
MUTE
MD
CDR
CD
AMP
AUX2
TUNER
BASS
TREBLE
STEREO
NIGHT
M-CH ST
REC
AUDI O
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
AUX1
A/D
MEMO
CL
DVDDV D VCRVCR
DSSDSS
TVTV
VOLUMEVOLUME
7.1CH IN7.1CH IN
2.
4.
1.
3.
1.
Select a desired Video source to decide the
routed video signal to the Monitor Outputs.
2.
Press the 7.1 CH INPUT button on the front
panel or press 7.1 CH on the remote to switch
the 7.1 channel input.
3.
If it is necessary to adjust the output level of
each channel, press the CH-SEL button on the
remote.
Adjust the speaker output levels so that you can
hear the same sound level from each speaker
at the listening position. For the front left, front
right, center, surround left, surround right and
surround back speakers, the output levels can
be adjusted between –12 to +12 dB.
The subwoofer can be adjusted between –18
and +12 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.
4.
Adjust the main volume with the MAIN VOLUME
knob or the VOL buttons on the remote.
To cancel the 7.1 CH. INPUT setting, press the 7.1
CH INPUT button on the front panel or press 7.1 CH
on the remote.
Notes:
• When the 7.1 CH. Input is in use, you may not select
a surround mode, as the external decoder determines
processing.
• In addition, there is no signal at the record outputs
when the 7.1 CH. Input is in use.
AUX2 INPUT
If you don’t need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX2 input.
In this case, You can connect additional audio source
to AUX2 as other audio input terminals.
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR6001
ME
N
PURE DIRECT HT-EQ
7.1CH
I
MODE AUTO
MULTI
PURE DIRECT
SURROUND
DSD
POWER ON/STANDBY
DISP MULTIAU TO
SLEEP
SURR
AUTO
LIP.SYNC
Depending on the image device (TV, monitor,
projector, etc.) connected to the SR6001, a time lag
can occur between image signal processing and
audio signal processing. Though minor, this time
lag can interfere with movie and music enjoyment.
The LIP.SYNC feature delays the audio signal with
respect to the image signal output from the SR6001
to correct the time lag between the sound and image.
It can be operated with the “LIP SYNC” and 1 and
2 cursor buttons of the remote controller. Set the
remote controller to the AMP mode before operating
the LIP.SYNC feature. The initial setting is OFF (0
ms).The time lag can be adjusted in 10 ms steps up
to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.
Note:
• The LIP.SYSNC feature turns OFF (0 ms) in
the SOURCE/PURE DIRECT mode. When the
SOURCE/PURE DIRECT mode is deactivated, the
set value of the LIP.SYSNC feature is automatically
restored.
CAT
P.SCAN
CAT
T.MODE
T.DISP
F.DIRECT
PTY
123
456
789
+10
00
HT-EQ
MULTI/
MENU
SPKR A/B
ENTER
EXIT
INFO
CH/
INPUT
T.T ONE
/SET UP
M-SPKR
MUTE
EX/ES
VIRTUAL
CS
dts
P.DIRECT
l/
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
REC
A/D
LIP SYNC/
MEMO
CL
VOLUMEVOLUME
7.1CH IN7.1CH IN
BAND