Filter
Top Products
H
lCORR
Parameter<inch>
Time Difference Table
Delay
Distance Distance
Delay
Distance
Distance
Number
(cm)
(inch)
Number
(cm)
(inch)
0
0.0
0.0
51
173.4
68.3
1 3.4
1,3
52
176.8
69.7
2 6.8 2.7
53
180.2 71.0
3 10.2 4.0
54 183.6 72.4
4
13,6
5.4
55
187.0 73.7
5
17.0
6.7
56
190,4 75,0
6 20.4 8.0
57
193.8
76.4
7
23.8 9.4
58 197.2
77,7
8
27,2
10.7
59 200.6
79.1
9
30,6
12.1
60
204.0
80.4
10
34.0 13.4
61
207.4
81.7
11
37.4 14.7
62
210.8
83.1
12
40.8
16.1
63
214,2
84.4
13
44,2
17.4
64 217.6
85,8
14 47.6
18,8
65
221,0
87.1
15
51,0
20.1
66 224.4
88.4
16 54.4
21.4 67 227.8
89,8
17
57.8
22.8
68
231,2
91.1
18
61,2
24.1
69 234.6 92.5
19
64.6
25,5
70
238,0
93.8
20
68,0
26.8
71
241.4
95,1
21
71.4
28.1
72
244,8
96.5
22
74,8
29.5
73 248.2 97.8
23 78.2 30.8 74 251.6
99.2
24
81,6
32.2 75 255.0 100.5
25
85.0
33.5 76 258.4 101.8
26
88.4 34.8
77
261,8 103,2
27 91.8
36.2 78 265.2 104.5
28
95.2
37,5
79 268.6
105,9
29 98.6 38.9
80
272.0 107.2
30 102.0 40.2
81
275.4 108.5
31
105.4
41,5
82
278.8 109.9
32
108.8 42.9
83
282.2
111,2
33
112.2 44.2
84
285,6
112.6
34
115,6
45.6
85
289.0 113.9
35
119.0 46.9
86
292.4
115.2
36
122.4
48,2
87 295.8
116.6
37 125.8 49.6
88
299.2 117.9
38
129.2 50.9
89
302.6 119.3
39
132.6
52,3
90
306.0 120.6
40
136,0
53.6
91
309.4
121,9
41
139.4
54.9 92
312.8 123.3
42
142.8
56.3 93
316.2 124.6
43
146.2 57.6 94 319.6 126.0
44 149.6
59.0 95
323.0 127.3
45
153,0 60,3
96
326.4 128.6
46 156.4
61,6
97
329.8
130.0
47
159.8 63.0 98
333.2 131.3
48 163.2 64.3 99 336.6
132,7
49
166.6
65.7
~
50
170,0
67.0
i8-EN
Setting
the
Time
Correction
Unit
You
can change the unit, (cm or inch)
of
time correction.
1 Press and hold
FUNC./SETUP
for at least 2
seconds to setup the Selection mode.
2 Turn the
Rotary
encoder
to select AUDIO mode,
and then press
~
III
lENT
.
Bluetooth H GENERAL H AUDIO H DISPLAY H
TUNER* H Bluetooth
* Only when HD Radio/SATRadio is connected.
3 Turn the
Rotary
encoder
to select T.CORR
Parameter mode, and then press
~/II/ENT.
4 Turn the
Rotary
encoder
to select the desired
items, and then press
~/II/ENT.
1
CaRR
Parameter
<cm>
(Initial setting)
5 After setting, press and hold
FUNC./SETUP
for
at
least 2 seconds to return to normal mode.
• Pressing
~
/RTN
during the procedure will return to the previous
mode.
•
If
no operation is peiformed
for
60 seconds
in
the SETUP mode, the
setting mode is canceled.
• Press and hold
C\
/Ese
for
at least 2 seconds, the setting mode is
canceled.
Adjusting
and
Storing
the
Time
Correction
Before performing the following procedures, refer to "About Time
Correction" (page 17).
1 Press A.SEL to recall the DSP adjust mode.
Media Xpander H Crossover H
lCorrection
H
Parametric EO/Graphic
EO
H Media Xpander
2 Turn the
Rotary
encoder
to select the
T.Correction mode, and then press
~/II/ENT.
3 Press
BAND
to select a
spea"ker
to be adjusted.
2.2ch (3WAY) System
L-F
(Initial setting)
~
R-F
~
L-R
~
R-R
~
(Mid-L) (Mid-R)
(High-L)
(High-R)
L-SW
~
R-SW
~
L-F
(Mid-L)
4.2ch (F/RISub-W) System
L-F
(Initial setting)
~
R-F
~
L-R
~
R-R
~
(Front-L) (Front-R) (Rear-L) (Rear-R)
L-SW
~
R-SW
~
L-F
(Front-L)