Filter
Top Products
Sound Setting
~
IESC Rotary encoder (AUDIO)
~/II/ENT,
SOURCEI<!.>
BAND
~
o
~/RTN
A. SEL FUNC.lSETUP Preset
buttons
MultEQ
(1
through
6)
Adjusting
BassfTrebleIBalance
(Between
Left
and
Right)/Fader
(Between
Front
and
Rear)/Defeat
1 Press
Rotary
encoder
(AUDIO)
repeatedly
to
choose the desired mode.
Each press changes the mode as follows:
SUBWOOFER*]
~
BASS*2
~
TREBLE*2
~
BALANCE
~
FADER*3
~
DEFEAT
~
VOLUME
~
SUBWOOFER*]
Subwoofer: 0 -
+15
Bass level:
-7-+7
Treble level:
-7-+7
Balance: L15 - R15
Fader: R15 - F15
Defeat: ON/OFF
Volume:
0 - 35
•
If
no operation is performed
for
5 seconds after selecting the
SUBWOOFER, BASS, TREBLE, BALANCE, FADER
or
DEFEAT
mode, the unit automatically returns to normalmode.
*1
When the subwoofer mode is set to
OFF,
its level cannot be adjusted.
~
When the MultEQ is setto
OFF,
its level cannot be adjusted.
*3
If
you set the 4.2ch/2.2ch switch (pages 40 to 42) to 2.2ch, you
cannot adjust the FADER mode.
2 Turn the
Rotary
encoder
(AUDIO)
until
the
desired
sound
is
obtained in each mode.
By setting
DEFEAT
ON, previously adjusted settings of
BASS, TREBLE and
EO
will return to the factory defaults
and
MX
(page 19)
is
turned off.
• Depending on the connected devices, somefunctions and display
indications do not work.
Turning
MultEQ
on/off
MultEQ, developed
by
Audyssey Labs, automatically corrects the audio
for the listening environment.
The
system is optimized for selected
positions
in
the vehicle. To accomplish this,
MultEQ
must
take
measurements
of
the vehicles responsecharacteristics.
For
details
on
the
set up procedure, consult your authorized Alpine dealer.
Press
MultEQ
to
select ON/OFF mode.
•
If
MultEQ
is
turned on and its button pressedand held
for
at least 2
seconds, the Curve mode is switched(only when curve1
and
curve2
are stored).
• When using MultEQ,
MX,
X-OVER, T.Correction, User's EQ,
Parametric EQ and Graphic EQ are setautomatically. They are no
longer user adjustable.
• When an external audio processoris connected, the MultEQfunction
cannot be used.
Equalizer
Presets
10 typical equalizer settings are preset at the factory for a variety
of
musical source material.
1 Press and
hold
FUNC./SETUP
for
at least 2
seconds
to
setup the Selection mode.
2 Turn the
Rotary
encoder
to
select AUDIO mode,
and then press
~/II/ENT.
Bluetooth H GENERAL H AUDIO H DISPLAY H
TUNER* H Bluetooth
* Only when HD Radio/SATRadio is connected.
3 Turn the
Rotary
encoder
to
select Factory's
EQ
mode, and then press
~/II/ENT.
4 Turn the
Rotary
encoder
to
select the desired
equalizer characteristic, and then press
~
III
lENT
.
Flat H Pops H Rock H News H Jazz&Blues H
Electrical Dance H Hip Hop&Rap H Easy Listening H
Country H Classical H User1 H User2 H User3 H
User4 H User5 H User6
• By selecting User's 1 to
6,
you can recall the storedpreset numberin
"Adjusting and Storing the Graphic Equalizer Curve" (page
14)
or
"Adjusting and Storing the Parametric Equalizer Curve
",
(page
14).
5 Press and
hold
FUNC./SETUP
for
at least 2
seconds
to
return
to
normal mode.
• Pressing
~
IRTN
during the procedure will return
to
the previous
mode.
•
If
no operation is performed
for
60 seconds
in
the SETUP mode, the
setting mode
is
canceled.
• This function is inoperable when DEFEATis setto
ON
(page 13).
• Press and hold
~
IESC
for
at least 2 seconds, the setting mode is
canceled.
13-EN