Filter
Top Products
ENGLISH
• R2 ~ is displayed on the front
panel for several seconds.
• Each time this button is pressed,
the ROOM 2 mode changes as follows :
OFF : To turn off the ROOM 2
function. ("R2" goes off.)
ON : To turn it on. ("R2" lights up.)
Note:
• When the ROOM 2 mode is set to OFF, the ROOM 2
input and the ROOM 2 volume cannot be selected.
34
ROOM 2 SOURCE PLAYBACK
When using the buttons on the remote control unit.
• This function allows enjoying one source in the main room and playing another in a different room at the same time.
• When you connect the multi-room system kit to the IR IN jack of this receiver, you can control this receiver with the remote
control unit in a different room. (For details, refer to "CONNECTING MULTI-ROOM SYSTEM KIT" on page 12.)
Notes:
• The analog signals from the EXTERNAL INs and the digital signals cannot be output to the different room, meaning no
playback in a different room.
• You cannot play the ROOM 2 source in any surround mode.
Press the ROOM 2 button.
1
When using the buttons on the front panel.
Press the ROOM 2 button to enter the
ROOM 2 mode.
1
Select the desired
input as a ROOM 2
source.
2
• Each time this button is pressed,
the ROOM 2 input can be selected
among TUNER, CD, AUX, TAPE,
VIDEO 1 ~ VIDEO 4.
Adjust the ROOM 2 volume.
3
Select the desired mode while displaying
the ROOM 2 setting mode.
2
• R2 ~ is displayed on the front panel for
several seconds.
• When the ROOM 2 setting mode
disappears, press the ROOM 2 button
again.
• Each time these buttons are pressed,
the mode changes as follows :
R2 ~ (ROOM 2 mode) : To turn on or
off the ROOM 2
function.
Input display (ROOM 2 input) : To select the desired
ROOM 2 source.
R2 V ~ (ROOM 2 volume) : To adjust the volume on
the power amplifier
assigned to ROOM 2.
Note:: When the ROOM 2 mode is set to OFF, the
ROOM 2 input and the ROOM 2 volume cannot
be selected.
Set the selected mode as desired.
3
Notes :
• Even when this receiver enters the standby mode, in such a case that "R2" lights up still and the POWER ON/STANDBY
button lights up in blue as it does in the operating mode, meaning only the ROOM 2 circuitry operates, the ROOM 2
source can be played independently.
• When the ROOM 2 function is operating in the standby mode, only the remote control unit is available.
• When you do not use the ROOM 2 function, turn off the ROOM 2 function to save electricity.
CONTROL
• You can adjust the volume on the
power amplifier assigned to ROOM
2 when the SURROUND BACK/
ROOM 2 speaker terminals are
connected to the speakers in a
different room. (For details, refer to
"When selecting the AMP ASSIGN"
on page 37.)
Start play on the component related to the
ROOM 2 source.
4
Start play on the component related to the
ROOM 2 source.
4
When selecting the ROOM 2 mode.
OFF : To turn off the ROOM 2
function. ("R2" goes off.)
ON : To turn it on. ("R2" lights up.)
When selecting the ROOM 2 input.
• You can select the desired among TUNER, CD, AUX,
TAPE, VIDEO 1 ~ VIDEO 4 as a ROOM 2 source.
When selecting the ROOM 2 volume.
• You can adjust the volume on the power amplifier
assigned to ROOM 2 when the SURROUND BACK/
ROOM 2 speaker terminals are connected to the
speakers in a different room. (For details, refer to
"When selecting the AMP ASSIGN" on page 37.)