Filter
Top Products
Controls and displays
02
13
En
10 Receiver Control buttons
Set the remote control operation selector switch to
RECEIVER fir st to access:
STATUS – Press to check selected receiver settings
(page 81).
PHASE CTRL – Press to switch on/off Phase Control
or Full Band Phase Control (page 63).
CH LEVEL – Press repeatedly to select a channel,
then use / to adjust the level (page 116).
THX – Press to select a Home THX listening mode
(page 60).
PQLS – Press to select the PQLS setting (page 75).
AUTO/ALC/DIRECT – Switches between Auto
Surround (page 59), Auto Level Control, Optimum
Surround mode and Stream Direct mode (page 62).
STEREO – Switches between stereo playback and
Front Stage Surround Advance modes (page 61).
STANDARD – Press for St
andard deco
ding and to
switch various modes (2 Pro Logic, Neo:6, etc.)
(page 59).
ADV SURR – Use to switch between the various
surround modes (page 61).
SIGNAL SEL – Use to select an input signal (page 62).
SLEEP – Use to put the receiver in sleep mode and
select the amount of time before sleep (page 81).
DIMMER – Dims or brightens the display (page 81).
A.ATT – Attenuates (lowers) the level of an analog
input signal to prevent distortion (page 80).
SBch – With this receiver, SBch cannot be used.
MCACC – Press to switch between MCACC presets
(page 62).
HDMI OUT – Switch the HDMI output terminal
(page 81).
11
LIGHT
Press to turn on/off the illumination for the buttons.
1
12 Remote control operation selector switch
Set to RECEIVER to operate the receiver, TV or SOURCE
to operate the TV or the source device.
When this switch is set to RECEIVER, the receiver can be
controlled (used to select the white commands). Also use
this switch to set up surround sound.
13
VOL +/–
Use to set the listening volume.
14
MUTE
Mutes the sound or restores the sound if it has been
muted (adjusting the volume also restores the sound).
Remote control display
2
Remote control display for infrared signal
transmission (default)
Remote control display for RF two-way
communications
3
1 Remote control operating zone indicator
This indicates which zone the remote control is currently
set to operate. The display indicates the setting of the
MULTI-ZONE operation selector switch.
Only when RF two-way communications:
The box display here indicates the communication status
between this remote control unit and the receiver.
(White box with black letters): Two-way
communications are established and the receiver’s
power is on.
Note
1Press and hold in the LIGHT button for 5 seconds to change the illumination mode 1 or 2. When set to LIGHT MODE 2 (default), the
illumination only lights when the remote control LIGHT button is pressed. When switched to LIGHT MODE 1, the illumination lights whenever
buttons are operated. Setting LIGHT MODE 1 will shorten the service life of the batteries.
2 The display lights when a remote control operation is performed, then turns off after 20 seconds if no other operation is performed. When in
the Remote Setup mode, the setup is canceled and the display turns off if no operation is performed for 1 minute (page 83).
3 • This is displayed when an RF adapter is connected to the receiver and paired with the remote control. For details, see Using the RF
communications function on page 91.
• Depending on the communications environment, two-way communications may not work well and the remote control display may not reflect
the receiver’s status.
MAIN SOURCEIR
iPod/USB
1 2 3 4
5
6
7
MAIN
VIDEO
RCV CTRLRF
AV RECEIVER
1. Adv MCACC
+12.0dB
1 2 3 4
56
89
10 11 12
MAIN
SC-37_35_UXJCB.book 13 ページ ２０１０年３月９日 火曜日 午前９時３２分