Filter
Top Products
The System Setup and Other Setup menus
12
119
En
The Other Setup menu
The Other Setup menu is where you can make
customized settings to reflect how you are using the
receiver.
1 Set the remote control to the receiver operation
mode, then press
HOME MENU
.
A Graphical User Interface (GUI) screen appears on your
TV. Use /// and ENTER to navigate through the
screens and select menu items. Press RETURN to
confirm and exit the current menu.
2 Select ‘
System Setup
’ from the
Home Menu
.
3 Select ‘
Other Setup
’, then press
ENTER
.
4 Select the setting you want to adjust.
If you are doing this for the first time, you may want to
adjust these settings in order:
• HDMI Setup – Synchronizes this receiver with your
Pioneer component supporting Control with HDMI
(page 73).
• Volume Setup – Sets up the volume-related
operations of this receiver (see below)
.
• Remote Control Mode Setup – Sets this receiver’s
remote control mode (see below).
• Flicker Reduction – Adjusts the way the GUI screen
looks (page 120).
• RF Remote Setup (SC-37 only) – Allows the CU-
RF100 to be used even when the receiver is in the
standby mode (page 120).
• EXTENSION Setup (SC-35 only) – Allows the CU-
RF100 to be used even when the receiver is in the
standby mode (page 120).
• Multi Ch In Setup –
Specifies the optional settings for
a multi-channel input
(page 120).
• Pairing Bluetooth Setup – Use to pair a Bluetooth
ADAPTER and Bluetooth wireless technology device
(page 58).
5 Make the adjustments necessary for each setting,
pressing
RETURN
to confirm after each screen.
Volume Setup
You can set the maximum volume of this receiver or
specify what the volume level will be when the power is
turned on.
1Select ‘
Volume Setup
’ from the
Other Setup
menu.
2 Select the
Power ON Level
setting you want.
The volume can be set so that it is always set to the same
level when the receiver’s power is turned on.
• LAST (default) – When the power is turned on, the
volume is set to the same level as when the power
was last turned off.
•“---” – When the power is turned on, the volume is set
to minimum level.
• –80.0dB to +12.0dB – Specify the volume to be set
when the power is turned on, in steps of 0.5 dB.
It is not possible to set a volume level greater than the
value specified at Volume Limit setup (see below).
3 Select the
Volume Limit
setting you want.
Use this function to limit the maximum volume. The
volume cannot be increased above the level set here,
even by operating MASTER VOLUME button (or the dial
on the front panel).
• OFF (default) – The maximum volume is not limited.
• –20.0dB/–10.0dB/0.0dB – The maximum volume is
limited to the value set here.
4 Select the
Mute Level
setting you want.
This sets how much the volume is to be turned down
when MUTE is pressed.
• FULL (default) – No sound.
• –40.0dB/–20.0dB – The volume will be turned down
to the level specified here.
5 When you’re finished, press
RETURN
.
You will return to the Other Setup menu.
Remote Control Mode Setup
• Default setting: 1
This sets this receiver’s remote control mode to prevent
erroneous operation when multiple units of the receiver
are being used.
1Select ‘
Remote Control Mode Setup
’ from the
Other Setup
menu.
2 Select the
Remote Control Mode
setting you want.
3Select “
OK
” to change the remote control mode.
4 Follow the instructions on the screen to change the
remote control’s setting.
See Operating multiple receivers on page 84 (SC-37)/
page 96 (SC-35).
5 When you’re finished, press
RETURN
.
You will return to the Other Setup menu.
SC-37_35_UXJCB.book 119 ページ ２０１０年３月９日 火曜日 午前９時３２分