Pioneer SC-37 Stereo Receiver User Manual


 
Using other functions
09
76
En
Chapter 9:
Using other functions
Important
•The procedure for setting the receiver operation
mode differs for the remote controls included with
the SC-37 and SC-35. For the SC-37’s remote control,
set the remote control operation selector switch to
RECEIVER. For the SC-35’s remote control, press the
button. When “set the remote control to
the receiver operation mode” is indicated in these
instructions, use the respective procedure described
above.
Setting the Audio options
There are a number of additional sound settings you can
make using the AUDIO PARAMETER menu. The
defaults, if not stated, are listed in bold.
Important
Note that if a setting doesn’t appear in the AUDIO
PARAMETER menu, it is unavailable due to the
current source, settings and status of the r eceiver.
1 Set the remote control to the receiver operation
mode, then press
AUDIO PARAMETER
.
2Use
/
to select the setting you want to adjust.
Depending on the current status/mode of the receiver,
certain options may not be able to be selected. Check the
table below for notes on this.
3Use
/
to set as necessary.
See the table below for the options available for each
setting.
4 Press
RETURN
to confirm and exit the menu.
Setting What it does Option(s)
MCACC
(MCACC
preset)
Selects your favorite MCACC
preset memory when multiple
preset memories are saved. When
an MCACC preset memory has
been renamed, the given name is
displayed.
M1. MEMORY 1
to
M6. MEMORY 6
Default:
M1. MEMORY 1
EQ
(Acoustic
Calibration
EQ)
Switches on/off the effects of EQ
Pro.
ON
OFF
S-WAVE
(Standing
Wave)
Switches on/off the effects of
Standing Wave Control.
ON
OFF
RECEIVER
DELAY
(Sound
Delay)
Some monitors have a slight
delay when showing video, so the
soundtrack will be slightly out of
sync with the picture. By adding a
bit of delay, you can adjust the
sound to match the presentation
of the video.
0.0 to 10.0
(frames)
1 second = 30
frames (NTSC)
Default: 0.0
MIDNIGHT Allows you to hear effective
surround sound of movies at low
volumes.
MIDNIGHT/
LOUDNESS
OFF
MIDNIGHT ON
LOUDNESS Used to get good bass and treble
from music sources at low
volumes.
LOUDNESS
ON
TONE
(Tone
Control)
Applies the treble and bass tone
controls to a source, or bypasses
them completely.
BYPASS
ON
BASS
a
Adjusts the amount of bass. –6 to +6 (dB)
Default: 0 (dB)
TREBLE
a
Adjusts the amount of treble. –6 to +6 (dB)
Default: 0 (dB)
S.RTRV
(Sound
Retriever)
With the Sound Retriever
function, DSP processing is used
to compensate for the loss of
audio data upon compression,
improving the sound’s sense of
density and modulation.
OFF
b
ON
DNR
(Digital
Noise
Reduction)
May improve the quality of sound
in a noisy source (for example,
video tape with lots of background
noise) when switched on.
OFF
ON
DIALOG E
(Dialog
Enhance
ment)
Localizes dialog in the center
channel to make it stand out from
other background sounds in a TV
or movie soundtrack. By moving
from UP1 through UP2 and UP3
up to UP4, you can make the
sound source seem to relocate
upwards.
OFF
FLAT
UP1/UP2/UP3/
UP4
c
Hi-bit32
(SC-37 only)
(Hi-bit32/
High-
Sampling)
Creates a wider dynamic range with
digital sources like CDs, DVDs or
BDs. Smoother, more delicate
musical expression can be achieved
by requantizing 16 bit PCM or 20 bit
compressed audio signals or 24 bit
compressed/lossless audio signals
to 32 bit.
OFF
ON
Hi-bit
(SC-35 only)
(High Bit/
High
Sampling)
Creates a wider dynamic range with
digital sources like CDs or DVDs.
Smoother, more delicate musical
expression can be achieved by
requantizing 16 bit PCM or 20 bit
compressed audio signals to 24 bit.
OFF
ON
Setting What it does Option(s)
SC-37_35_UXJCB.book 76 ページ 2010年3月9日 火曜日 午前9時32分