Filter
Top Products
2.4 Software Packages to be Used
2 - 9
1
OVERVIEW
2
SYSTEM
CONFIGURATION
3
PERFORMANCE
4
NAMES OF
THE PARTS AND
THEIR SETTINGS
5
ROUGH
PRE-OPERATION
PROCEDURE
6
HANDLING
7
MAINTENANCE AND
INSPECTION
8
EMC DIRECTIVE
*1 The printer of ESC/P raster specifications such as the PM series cannot be connected and used with the GOT.
*2 The RS-422/RS-232C cable for use between GOT and computer link module should be fabricated on the user side
by referring to the [GOT-A900 Series User's Manual (Connection System Manual)].
*3 The RS-232C cable may be fabricated by the user.
The RS-232C cable can also be fabricated by the user.
Refer to the following manual for details of the cable specifications.
When GT Designer is used: GT Works Version /GT Designer Version Reference Manual
When GT Designer2 is used: GT Designer2 Version Operating Manual
*4 The printer cable may be fabricated by the user.
Refer to [A9GT-50PRF type Printer interface module User’s Manual] for full information on the specifications
needed to fabricate the cable.
*5 For the A9GT-QJ71LP23 and A9GT-QJ71BR13, the device range (QCPU, QnACPU, ACPU) that can be monitored
changes depending on the communication driver.
When the A7GT-J71LP23 or A7GT-J71BR13 is mounted, only the device range of the AnA can be monitored.
*6 Relevant document Some devices have been concluded to be applicable for GOT900 series by Mitsubishi.
For details of the devices, refer to the relevant document "List of valid devices applicable for GOT900 series "
(Technical bulletin T10-0028).
Please contact your local Mitsubishi representative for the document, if necessary.
The GOT may not operate correctly if a device other than described in the document is used.
*7 The A8GT-C100EXSS-1, A8GT-C200EXSS-1, and A8GT-C300EXSS-1 are composed of the A8GT-EXCNB (0.5m)
and the
A8GT-C100BS (10m), A8GT-C200BS (20m), and A8GT-C300BS (30m) respectively.
When calculating the cable length, the A8GT-EXCNB‘s cable length can be ignored.
2.4 Software Packages to be Used
When a GOT is used, a software package of the applicable version or later is required.
The versions of the software packages required for each GOT are shown below.
RS-422 cable
AC30R4-25P Cable length 3m (D-sub 25-pin at both ends)
For connection between GOT and A/
QnACPU
For connection between GOT and FXCPU
AC100R4-25P Cable length 10m (D-sub 25-pin at both ends)
AC300R4-25P Cable length 30m (D-sub 25-pin at both ends)
---
For connection between GOT and computer link module *
2
RS-232C cable *
3
QC30R2 Cable length 3m For connection between GOT and QCPU
AC30R2-9P Cable length 3m (D-sub 9-pin, D-sub 25-pin)
For connection between GOT and personal
computer for data transfer
AC30R2-9SS Cable length 3m (D-sub 9-pin at both ends)
AC30R2 Cable length 3m (D-sub 25-pin at both ends)
For connection between GOT and personal
computer for data transfer
(9-pin conversion connector required)
AC30N2A Cable length 3m (D-sub 25-pin at both ends)
---
For connection between GOT and computer link module *
2
---
For connecting the GOT with the power supply unit of the bar code reader *
4
Printer cable *4 AC30PIO-20P Cable length 3m For connection between GOT and printer
GT Designer ---
Screen creation software for GOT900 series
GT Designer 2 ---
Component Type Description