Filter
Top Products
11
ENGLISH
DIGITALDIGITAL
ININ
OUTOUT
DIG-1 INDIG-1 IN DIG-2 INDIG-2 IN
DIG.OUTDIG.OUT
OPTOPT
DIG-4 INDIG-4 INDIG-3 INDIG-3 IN
DIG.OUTDIG.OUT
COAXCOAX
SURROUNDSURROUND
BACKBACK
RRSURROUNDSURROUND LLLL FRONTFRONTCENTERCENTER RR
VIDEOVIDEO
S-VIDEOS-VIDEO
ININOUTOUTININOUTOUTININOUTOUTININ ININININ OUTOUT
DSSDSS
//
VCR2VCR2VCR1VCR1DVDDVD
AUDIOAUDIO
TVTV TAPETAPE CDCDCDRCDR
//
MDMD
SUBSUB
WOOFERWOOFER
CENTERCENTER CECENTER
FRONTFRONT FRONT
SURROUND
SUSURR.
BBACK
SURROUNDSURROUND
SUBSUB
WOOFERWOOFER
SURR.SURR.
BACKBACK
6.1CH INPUT6.1CH INPUT
L
R
ININ
MONITORMONITOR
OUTOUT
VCR1 OUTVCR1 OUT
VCR1 INVCR1 INDVD INDVD IN
LL
RR
ININININ OUTOUTOUTOUT
PRE OUT
OUTOUT
MONITORMONITOR
ININ
TVTV DSSDSS
//
VCR2VCR2DVDDVD VCR1VCR1
ININ
GNDGND
AMAM
FMFM
ANTENNAANTENNA
((
7575
ΩΩ
))
REMOTEREMOTE
CONTROLCONTROL
SWITCHED 100W MAXSWITCHED 100W MAX
SPEAKER SYSTEMSSPEAKER SYSTEMS AC OUTLETAC OUTLETDIGITALDIGITAL
DIG-1 INDIG-1 IN
DIG.OUTDIG.OUT
OPTOPT
DIG-4 INDIG-4 IN
ININOUTOUTININOUTOUTININ
AUDIOAUDIO
TAPETAPE CDCDCDRCDR
//
MDMD
LL
RR
OUT IN
L
R
L
R
OUT
L
R
L R
L R
L R
RLLR RL
OUT IN
L
R
L
R
DIGITAL
OUTPUT
DIGITAL
OUTPUT
DIGITAL
INPUT
R L
L R L R
RL
L R
ANALOG AUDIO
DIGITAL AUDIO
(COAXIAL)
DIGITAL AUDIO
(OPTICAL)
CONNECTING AUDIO COMPONENTS
The output audio signal from the TAPE OUT jack
and the CD-R/MD OUT jack is the sound source
currently selected.
Caution:
• Do not connect this unit and other components to
mains power until all connections between
components have been completed.
Notes:
• Insert all plugs and connectors securely.
Incomplete connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R(right) channel, and
white connectors are for the L(left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that
is connected with this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables will result in
generating hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
• There are four digital inputs, two coaxial jacks
and two optical jacks, on the rear panel. You can
use these jacks to input PCM, Dolby Digital and
DTS bitstream signals from a CD, DVD, or other
digital source components.
• There are one digital output with coaxial jack
and one with optical jack on the rear panel.
These jacks can be connected to CD recorder,
MD deck.
• Setup the digital audio format of DVD player, or
other digital source component. Refer to the
instructions for each component to be
connected to digital input jacks.
• Use fiber optical cables(optical) for DIG-1,2
input jacks. Use 75 ohms coaxial cables(for
digital audio or video) for DIG-3,4 input jacks.
• You can designate the input for each digital
input/output jacks according to your component.
See page 16.
Notes:
• There is no Dolby Digital RF input jack. Please
use an external RF demodulator Dolby Digital
decoder when connecting the Dolby Digital RF
output jack of the video disc player to the digital
input jack.
• The digital signal jacks on this unit conform to the
EIA standard. If you use a cable that does not
conform to this standard, this unit may not
function properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks
are output through the corresponding digital and
analog jacks, respectively.
1. 2.
3. 4. 5.
CONNECTING SPEAKER WIRE
1.
Strip away approx. 10 mm of wire insulation.
2.
Twist the bared wire ends tight to prevent
short circuits.
3.
Loosen the knob by turning counterclockwise.
4.
Insert the bare part of the wire into the hole in
the side of each terminal.
5.
Tighten the knob by turning clockwise to
secure the wire.
Cautions:
• Be sure to use speakers with the specified
impedance shown on the rear panel of this unit.
• To prevent damage
to circuitry, do not
let the bare speaker
wires touch each
other and do not let
them touch any metal
part of this unit.
• Do not touch the speaker terminals when the
power is on. It may cause electric shocks.
• Do not connect more than one speaker cable to
one speaker terminal. Doing so may damage this
unit.
Note:
• Be sure to connect the positive and negative
cables for the speaker properly. If they are miss-
connected, the signal phase will reversed and the
signal quality will be corrupted.
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect
a powered subwoofer (power amplifier built in ).
If your subwoofer is passive type (power amplifier
is not built in), connect a monaural power amplifier
to the PRE OUT SUBWOOFER jack and connect
the subwoofer to the amplifier.
3/8 inch
(10 mm)
CD RECORDER / MD DECK
CD PLAYER
TAPE DECK
03.4.10, 3:00 PMPage 11