Filter
Top Products
8
ENGLISH
SCANNING THE CODE TABLE
1.
Switch on the appliance which should be
controlled.
2.
Press and hold down the function button for
appliance which should be controlled and
press SETUP until the indicator blinking
twice.
3.
Press the code 9 - 9 - 1.
The indicator will blink twice.
4.
Aim the remote control at the appliance and
slowly alternate between pressing POWER
and the function button for the appliance.
5.
Stop when the appliance turns off.
6.
Press SETUP once to lock in the code.
CHECKING THE CODE
1.
Press and hold down the function button for
appliance which should be controlled and
press SETUP until the indicator blinking twice.
2.
Press the code 9 - 9 - 0.
The indicator will blink twice.
3.
To view the code for first digit, press 1 once.
Wait 3 seconds, count the indicator blinks
(e.g. 3 blinks = 3) and write down the number.
Note:
If a code digit is “0”, the indicator will not blink.
4.
Repeat step 3 three more times for remaining
digits. Use 2 for the second digit, 3 for the
third digit, and 4 for the fourth digit.
RESETTING THE ALL CODE
1.
Press and hold down the any function button
and press SETUP until the indicator blinking
twice.
2.
Press the code 9 - 8 - 1.
The indicator will blink twice.
Then, RC5400SR will return to the factory
preset code.
Note:
After this procedure, the selected function
button is set initial code and other function
buttons are set initial code too.
Once you have found and the codes for your various
appliances, you may want to write them down here.
TV
VCR
DSS
DVD
CD
TAPE
CDR
MD
OPERATION OF REMOTE CONTROL
UNIT
REMOTE CONTROL
The distance between the transmitter of the
remote control unit and the IR SENSOR of the
SR4400 should be less than about 5 meters. If the
transmitter is pointed to a direction other than the
IR SENSOR or if there is an obstacle between
them, remote control may not be possible.
Remote-controllable range
LOADING BATTERIES
The life of the batteries used with the remote
control unit is about 4 months with normal use.
Also be sure to replace batteries earlier when you
notice that they are getting weak.
1.
Remove the back cover.
2.
Insert the new batteries (AAA type) with
correct
and polarity.
Remote control unit (RC5400SR)
60°
SR4400
Approx. 5 m
3.
Close until it clicks.
MENU
OSD
SLEEP
MUTE
AMPAUX
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
VOL.VOL.
TV
MAIN
2.
TUNE/SEARCH
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN
6.1CH IN
STEREO
M-CH ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII EX/ES DSP
DTS
S-DIRECT
AUTO
321
654
98
0
7
T.TONE
MENU OFF
SETUP/
MENU
OSD
OK
2.
6.
3.
MENU
OSD
SLEEP
MUTE
AMPAUX
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
VOL.VOL.
TV
MAIN
F.DIRECT
DISP./RDS
TUNE/SEARCH
MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN
6.1CH IN
STEREO
M-CH ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII EX/ES DSP
DTS
S-DIRECT
AUTO
321
654
98
0
7
T.TONE
MENU OFF
SETUP/
OK
1.
3.
4.
2.
MENU
OSD
SLEEP
MUTE
AMPAUX
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
VOL.VOL.
TV
MAIN
1.
TUNE/SEARCH
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN
6.1CH IN
STEREO
M-CH ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII EX/ES DSP
DTS
S-DIRECT
AUTO
321
654
98
0
7
T.TONE
MENU OFF
SETUP/
MENU
OSD
OK
1.
2.
03.4.10, 3:00 PMPage 8