Marantz SR4400 Stereo Receiver User Manual


  Open as PDF
of 36
 
26
ENGLISH
MANUAL TUNING
(USING THE SR4400)
1.
To select tuner and desired band (FM or AM),
press the TUNER button on the front panel
2.
Press the F/P(Frequency/Preset) button on
front panel to appears frequency on the
display.
3.
Press the TUNING or button.
(Using the remote control unit)
1.
To select tuner and desired band (FM or AM),
press TUNER button twice within in two
seconds on the remote.
2.
Press
55
55
5 or
66
66
6 on the remote to tune in the
desired station.
DIRECT FREQUENCY CALL
1.
To select tuner and desired band (FM or AM),
press the TUNER on the remote.
2.
Press the F.DIRECT button on the remote,
display will show “FREQ - - - ”.
3.
Input your desired station’s frequency with
numeric buttons on the remote.
4.
The desired station will automatically be
tuned.
1.
Select a desired Video source to decide the
routed video signal to the Monitor Outputs .
2.
Press the 6.1 CH-IN button on the front panel
or on the remote to switch the 6.1 channel
input.
3.
If necessary to adjust the output level of each
channel, use “6.1 Ch. INPUT LEVEL” in
SETUP menu system as desired.
Adjust the speaker output levels so that you
can hear the same sound level from each
speaker at the listening position. For the front
left, front right, center, surround left, surround
right and surround back speakers, the output
levels can be adjusted between –10 to +10
dB.
The subwoofer can be adjusted between –15
and +10 dB.
These adjusting result will be stored to 6.1 Ch.
INPUT condition. (see to page 20)
4.
Adjust the main volume with the MAIN
VOLUME knob or the VOL buttons on the
remote.
To cancel the 6.1 Ch. INPUT setting, press the 6.1
CH-IN button on the front panel or on the remote.
Notes:
• When the 6.1 Ch. Input is in use, you may not
select a surround mode, as the external decoder
determines processing.
• In addition, there is no signal at the record outputs
when the 6.1 Ch. Input is in use.
(FM) TUNING MODE (AUTO STEREO OR MONO)
When in the auto stereo mode, AUTO indicator
keeps to light on the display.
The “ST” indicator lights on when a stereo
broadcast is tuned in.
At open frequencies, the noise is muted and the
“TUNED” and “ST” indicators turn off.
If the signal is weak, it may be difficult to tune into
the station in stereo. In such a case, press the
MODE button on the front panel or on the remote.
“AUTO” indicators turn off ,FM stereo broadcasts
are received in monaural and the “ST” indicator
turns off.
To return to auto stereo mode, press the MODE
button on the front panel or on the remote again.
AUTO indicator lights on the display.
PRESET MEMORY
With this unit you can preset up to 30 FM/AM
stations in any order.
For each station, you can memorize the frequency
and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
1.
To select FM , press the TUNER button on the
front panel.
2.
While pressing the MEMORY button, press
the TUNING button to up.
BASIC OPERATION
(TUNER)
LISTENING TO THE TUNER
Frequency scan step for AM is selectable.
Default setup is 10 kHz step, if your country’s
standard is 9 kHz step, Press TUNER button on
the remote more than 6 seconds. Scan step will
change.
Note:
• Preset memory for the tuner will clear by
changing this setup.
AUTO TUNING
(USING THE SR4400)
1.
To select tuner and desired band (FM or AM),
press the TUNER button on the front panel.
2.
Press the F/P(Frequency/Preset) button on
the front panel to appears frequency on the
display.
3.
Press the TUNING or button on the front
panel for more than 1 second to start the Auto
tuning function.
4.
Automatic searching begins then stops when
a station is tuned in.
(Using the remote control unit)
1.
To select tuner and desired band (FM or AM),
press the TUNER button twice within in two
seconds on the remote.
2.
Press
55
55
5 or
66
66
6
more than 1 second on the
remote.
3.
Automatic searching begins then stops when
a station is tuned in.
If tuning does not stop at the desired station, use to
the “Manual tuning” operation.
PTY
ATT.
F.DIRECT
DISP./RDS
TUNE/SEARCH
MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN
MEMO
CLEAR
0
+/A
/VCR
/ANT
–/B
2.
F/P
MODE
ET
MUTE
CDR/MD
TAPE
CD
TUNER
DISPLAY
UP
VOLUME
DOWN
MODE
PTY
ATT
F.DIRECT
DISP./RDS
TUNE/SEARCH
MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN
6.1CH IN
STEREO
M-CH ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII EX/ES DSP
DTS
S-DIRECT
AUTO
321
654
98
0
7
T.TONE
MENU OFF
SETUP/
/A
/VCR
/ANT
/B
2.
CLEAR
F/P
MODE
TUNING/PRESET
MEMORY
MUTE
S-DIRECT
HT-EQ
DSS/VCR2
DVD
CDR/MD
TAPE
CD
TUNER
TV
DISPLAY
VCR1
VOL
DOWN
F/P
TUNING/PRESET
TUNER
3. 2. 1.
CLEAR
F/P
MODE
TUNING/PRESET
MEMORY
PHONES
SURROUND
STANDBY
POWER ON/STANDBY
MUTE
S-DIRECT
HT-EQ
DSS/VCR2
DVD
CDR/MD
TAPE
CD
TUNER
TV
A/D
DISPLAY
VCR1
UP
VOLUME
DOWN
AV SURROUND RECEIVER SR4400
CH-IN
6.1
AV SURROUND RECEIVER SR4400
CH-IN
6.1
TUNING/PRESET
TUNER
CLEAR
MEMORY
MODE
2.4.2.5. 3.
2)
1. 3.
1)
CLEAR
F/P
MODE
TUNING/PRESET
MEMORY
MUTE
S-DIRECT
HT-EQ
DSS/VCR2
DVD
CDR/MD
TAPE
CD
TUNER
TV
DISPLAY
VCR1
V
DOWN
F/P
TUNING/PRESET
TUNER
3. 2. 1.
CLEAR
MEMORY
PHONES
SURROUND
STANDBY
POWER ON/STANDBY
HT-EQ
DVD
TV
A/D
VCR1
AV SURROUND RECEIVER SR4400
CH-IN
6.1
AV SURROUND RECEIVER SR4400
CH-IN
6.1
CH-IN
6.1
CH-IN
6.1
2.
SLEEP
MUTE
AMPAUX
TUNER
CD
TAPE
CDR/MD
DVD
VCR1
DSS/VCR2
TV
VOL.VOL.
TV MAIN
1.
PTY
ATT.
F.DIRECT
DISP./RDS
TUNE/SEARCH
MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN
MEMO
CLEAR
0
+/A
/VCR
/ANT
–/B
2.
SLEEP
MUTE
AMPAUX
TUNER
CD
TAPE
CDR/MD
DVD
VCR1
DSS/VCR2
TV
VOL.VOL.
TV MAIN
1.
MENU
OSD
SLEEP
MUTE
AMPAUX
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
VOL.VOL.
TV
1.
DISC/DECK
PTY
ATT.
F.DIRECT
DISP./RDS
TUNE/SEARCH
MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN
6.1CH IN
STEREO
M-CH ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII EX/ES DSP
DTS
S-DIRECT
AUTO
321
654
98
0
7
SYSTEM REMOTE CONTROLLER
+/A
/VCR
/ANT
–/B
3.
2.
DISC/DECK
PTY
ATT.
F.DIRECT
DISP./RDS
MODE
SYSTEM REMOTE CONTROLLER
RC5400SR
+/A
/VCR
/ANT
–/B
03.4.10, 3:01 PMPage 26
 previous next