47
Additional Information
Playing Back a Disc/USB Mass Storage Class Device:
JVC bears no responsibility for any loss of data in
the USB mass storage class device while using this
System.
• When you change the source to “DVD/CD” or
“USB,” it may take a while to activate the source.
• While the System is reading a disc, the source may
not change to “USB” properly. In this case, press 7,
then change the source to “USB.”
• On some discs, the actual operations may be
different from what is explained in this manual
due to the programming and disc structure; such
differences are not a malfunction of this System.
• The System recognizes up to 999 tracks (files) per
group, and 99 groups per disc/USB mass storage
class device. The total number of tracks (files) that
the System can detect is 4 000.
– If there are any unplayable files in a folder, those
files are also counted in the total file number.
– Playable files which do not belong to any groups
are handled as GROUP1.
• For playback of files in the USB mass storage class
device...
– When connecting a USB mass storage class device,
refer also to its manual.
– Connect one USB mass storage class device to the
System at a time. Do not use a USB hub.
– You cannot charge any USB mass storage class
device through the USB REC/PLAY (
)
terminal.
– While playing back a file in a USB mass storage
class device, do not disconnect the device. It may
cause malfunction on both the System and the
device.
– This System is compatible with USB 2.0 Full
Speed.
– You cannot play back a file larger than 2
Gigabytes.
– When playing a file of a large transfer rate, frames
or sounds may be dropped during playback.
– This System cannot recognize a USB mass storage
class device whose rating is other than 5 V and
exceeds 500 mA.
– This System may not play back some USB mass
storage class devices and does not support DRM
(Digital Rights Management).
– It will take some time to start up a digital audio
player whose contents are larger than 1 Gigabyte.
Learning More about This System
Connections (see pages 4 to 7)
• Make sure the antenna conductors do not touch any
other terminals, connecting cords or the power cord.
Also, keep the antennas away from metallic parts of
the System, connecting cords, and the power cord.
These could cause poor reception.
• Use only speakers with the same speaker impedance
as indicated by the speaker terminals on the rear of
the System.
• The speakers are magnetically shielded to avoid
color distortions on TVs. However, if not installed
properly, it may cause color distortions. So, pay
attention to the following when installing the
speakers.
– When placing the speakers near a TV set, turn off
the TV’s main power switch or unplug it before
installing the speakers.
Then wait at least 30 minutes before turning on
the TV’s main power switch again.
– Some TVs may still be affected even though
you have followed the above instructions. If this
happens, move the speakers away from the TV.
Changing the Color System and Scanning Mode:
• You cannot change the scanning mode to progressive
in the following cases:
– When your TV does not support the progressive
video input.
– When you have not connected your TV to the
system using a component video cord.
Daily Operations—Playback (see pages 9 to
14)
• Instead of pressing , the System is turned on
by pressing one of the source buttons, the DOOR
OPEN/CLOSE button or 0 on the main unit.
Listening to the Radio:
• If you store a new station into an occupied preset
number, the previously stored station in that number
will be erased.
• When you unplug the power cord or if a power
failure occurs, the preset stations will be erased in a
few days. If this happens, preset the stations again.
text_EN_NXG7G3.indb 47text_EN_NXG7G3.indb 47 08.7.14 11:42:23 AM08.7.14 11:42:23 AM