Filter
Top Products
73
Troubleshooting guide
VIDEO and AUDIO
Desired picture does not appear.
• Improper connection.
➞Check the connection again. Insert the plugs and connectors
completely.
No OSD Menu display.
• Improper connection.
➞Check connections.
• OSD Menu is displayed when monitor is connected to VIDEO or
S VIDEO of MONITOR OUT.
➞Confirm connections (see page 19).
No sound, or sound of the selected source is not heard.
• Input Setup menu settings are incorrect.
➞Check settings (see page 34).
No picture appears on the TV screen (or monitor).
• TV (or monitor) is not set to receive the output signals from the
receiver.
➞Set the TV (or monitor) to the receiver input.
• Video cable is not connected securely.
➞Check connections.
• You have connected to the COMPONENT VIDEO connectors
but the DTR-7.2 is not set properly.
➞Check the Video Setup submenu of the Input Setup menu
(page 36).
REMOTE CONTROLLER
Front panel controls function but remote controller
controls do not.
• No batteries in remote controller.
➞Insert batteries.
• Batteries have worn out.
➞Replace batteries.
• Remote controller is not pointed at the remote sensor of the
DTR-7.2.
➞Point the remote controller at the remote sensor of the DTR-
7.2.
• Remote controller is too far from the DTR-7.2.
➞Operate the remote controller within 16 feet (5 meters).
• Remote controller is functioning in a different mode
➞Press the RCVR MODE button.
OTHER
LATE NIGHT function cannot be used.
• Playback source is not Dolby Digital encoded.
➞Check that the DOLBY DIGITAL indicator lights up on the
display.
Re-EQ function cannot be used.
• Listening mode is set to Theater-Dimensional, Direct, PL II
Music, or Neo:6 Music.
➞See page 44.
Parameter cannot be set for Front Effect etc.
• Parameter may not be able to be set depending on the listening
mode.
➞See table on page 45.
If one of the messages shown below appears
“Not available with headphones use”
The operation is not allowed because headphones are plugged into
the DTR-7.2.
“Not available with Multichannel use”
Cannot be used while the multi-channel output is being used.
“Not available in this Sp Config”
Will not work with the current speaker configuration settings.
“Not available in Zone 2 mode”
The operation is not allowed because the Zone 2 mode is turned on.
“Only available with Dolby D”
No setting other than Dolby Digital can be set.
“Not available in this Listening mode”
Will not work with the current listening mode.
“Not available with this signal”
The listening mode cannot be selected with the current input source.
“Not available with Muting”
Will not work because the muting is activated.
“Zone 2 is not On”
Will not work because the Zone 2 has not been turned on.
Multichannel audio is not output.
• To listen to multichannel audio, “Yes” must be selected in the
“Multichannel” in the Multichannel setup sub-menu of the Input
Setup menu. Also, it is necessary to select Multichannel with the
Audio Selector button.
➞Check that the component is connected to the MULTI
CHANNEL INPUT port and check the Setup menu settings.
Components in remote zone (Zone 2) do not operate
properly.
• Components are incorrectly connected.
➞Check connections.
• Objects are interfering with remote controller signals.
➞Move inferring objects away from path of remote controller
signals.
Also refer to the respective instruction manuals of the compact disc
player, DVD player, video cassette recorder, TV monitor, etc., that
compose your entertainment system.
The DTR-7.2 contains an internal microcomputer that performs
high-level operations. However, on extremely rare occasions, noise
or interference from an external source or static electricity may cause
faulty operation. If this occurs, unplug the power cord from the wall
outlet, wait five or more seconds, and then plug it back in. This
should correct the situation.
* To reset the surround mode and other settings to the factory
default settings, hold down the Video 1 button with the DTR-7.2
turned on and then press the Standby/On button. “CLEAR”
appears in the front display and the DTR-7.2 enters the standby
state.