Filter
Top Products
30
Speaker Setup
1-1. Speaker Config sub-menu
Here you will enter which speakers are connected and the size of
each speaker.
a. Subwoofer
Yes: Select when a subwoofer is connected.
No: Select when a subwoofer is not connected.
b. Front
Large: Select if the front speakers are large sized.
Small: Select if the front speakers are small sized.
• If “No” is selected for the Subwoofer setting, then this setting
is fixed to “Large.”
c. Center
None: Select if no center speaker is connected.
Large: Select if the center speaker is large sized.
Small: Select if the center speaker is small sized.
• If “Small” is selected for the Front setting, then “Large”
cannot be selected for this setting.
d. Surround L/R
None: Select if no surround left and right speakers are
connected.
Large: Select if the surround left and right speakers are large sized.
Small: Select if the surround left and right speakers are small sized.
• If “Small” is selected for the Front setting, then “Large”
cannot be selected for this setting.
e. Surround Bk
None: Select if no surround back left and right speakers are connected.
Large: Select if the surround back left and right speakers are large sized.
Small: Select if the surround back left and right speakers are
small sized.
• If “None” is selected for the Surround L/R setting, the display
disappears from the screen.
• If “Small” is selected for the Surround L/R setting, then
“Large” cannot be selected for this setting.
f. Surr Back Out
1ch: Select if there is only one surround back speaker.
2ch (PREOUT only): Select if there are two surround back
speakers. (For preout output only.)
Memo:
(Only one surround back
speaker)
Tip:
When setting the speaker size in the Speaker Config sub-menu, use
the guidelines given below.
Large: The complete frequency range for the channel you are
setting will be output from the speaker.
Small: Frequencies of the channel you are setting lower than 80
Hz will be output from the subwoofer. If there is no subwoofer,
then the output will be from the left and right front speakers. (Set
all speakers for THX speaker systems to “Small.”)
1. Speaker Setup menu
After you have installed the DTR-7.2, connected all the components,
and determined the speaker layout, it is now time to perform the
settings in the Speaker Setup menu for the optimum sound acoustics
for your environment and speaker layout.
Before you perform the following settings, it is important that you
first determine the following characteristics:
• The types and sizes of the speakers that are connected.
• The distance from each speaker to your normal listening
position.
Advanced Menu
1.Speaker Setup
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Bass Peak Level
|ENTER| Quit:|OSD|
1-1.Speaker Config
a.Subwoofer :Yes
b.Front :Small
c.Center :Small
d.Surr L/R :Small
e.Surr Back :Small
f.Surr Back Out :1ch
Quit:|SETUP|
SB
Front
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
Front
SW Center
Monitor
SL SR
[ ]
m/ft
[ ]
m/ft
SL SR
SBL SBR
Front
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
[ ]
m/ft
Front
SW Center
Monitor
(Two surround back speakers)
(Only one surround back
speaker)
(Two surround back speakers)
Advanced Menu
1.Speaker Setup
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Bass Peak Level
Quit:|SETUP|
|ENTER|Quit:|SETUP|
Basic Menu
1.Speaker Setup
1.Speaker Config
2.Speaker Distance
3.Level Calibration
|ENTER|Quit:|SETUP|