Filter
Top Products
82
Advanced Setup—Continued
HDMI Audio Out
This preference determines whether audio received at
the HDMI IN is output by the HDMI OUT. You may
want to turn this preference on if your TV is connected
to the HDMI OUT and you want to listen to the audio
from a component that’s connected to an HDMI IN,
through your TV’s speakers. Normally, this should be set
to Off.
Off: HDMI audio is not output (default).
On: HDMI audio is output.
Notes:
• If On is selected and the signal can be output by the
TV, the AV receiver will output no sound through its
speakers.
• When TV Control is enabled, this setting is set to
Auto.
• With some TVs and input signals, no sound may be
output even when this setting is set to On.
Lip Sync
The AV receiver can be set to automatically correct any
delay between the video and the audio, based on the data
from the connected monitor.
Disable: HDMI lip sync disabled.
Enable: HDMI lip sync enabled.
Notes:
• This function works only if your HDMI-compatible
TV supports HDMI Lip Sync.
• You can check the amount of delay being applied by
the HDMI Lip Sync function on the A/V Sync screen
(see page 78).
xvYCC
If you set the xvYCC color function to Enable while a
source and monitor that both support the xvYCC color
standard are connected to HDMI, the color quality will
be improved.
Disable: xvYCC color disabled.
Enable: xvYCC color enabled.
Notes:
• If the color is unnatural when xvYCC color is set to
Enable, change the setting to Disable.
• Refer to the connected component’s instruction man-
ual for details.
Control
This function allows CEC-standard-compatible equip-
ment connected to HDMI and -compatible
equipment to be operated together with the AV receiver.
Disable: HDMI Control disabled.
Enable: HDMI Control enabled.
Notes:
• Set to Disable when a connected piece of equipment is
not compatible or it is unclear whether the equipment
is compatible or not.
• If movement is unnatural when set to Enable, change
the setting to Disable.
• Refer to the connected component’s instruction man-
ual for details.
■ Power Control
To link the electrical connection of CEC-standard-com-
patible equipment and -compatible equipment
by means of HDMI, set to Enable. However, it may not
be possible to power link equipment, depending on the
settings and compatibility of the connected equipment.
Disable: Power Control disabled.
Enable: Power Control enabled.
Notes:
• The Power Control setting can be set only when the
above Control setting is set to Enable.
• HDMI power control only works with -com-
patible components that support it.
• When set to Enable, power consumption will increase.
(North American model)
• The AV receiver enters Ready mode when set to
Standby. (Australian model)
• Refer to the connected component’s instruction man-
ual for details.
■ TV Control
Set to Enable when you want to control the AV receiver
from an RIHD-compatible TV that is connected to
HDMI.
Disable: TV Control disabled.
Enable: TV Control enabled.
Notes:
• Set to Disable when the TV is not compatible or when
it is unclear whether the TV is compatible or not.
• The TV Control setting can be set only when the
above Control and Power Control settings are both set
to Enable.
• Refer to the connected component’s instruction man-
ual for details.
Notes:
• After changing the settings of the Control, Power
Control, or TV Control, turn off the power to all
connected pieces of equipment and then turn on
again. Refer to the User’s Manuals for all con-
nected pieces of equipment.
• When HDMI Audio Out is set to “On” or the TV
Control is set to “Enable” and the audio is playing
through the TV speakers, if the volume is
adjusted on the AV receiver, the audio will begin
to play through the speakers connected to the AV
receiver. If you want to turn off the audio from the
AV receiver, repeat the set up operation, and the
set up for the TV, or turn down the volume to its
lowest level.