Filter
Top Products
64
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confi rm the setting Return to previous menu
Set up speakers
Front B
Select the Front B setting to use
the second set of front speakers
for playback. In this case, go to
step 5.
11CH
Select the 11CH setting to
perform playback using up to 11.2
channels using a combination of
the unit's built-in power amplifi er
for 9-channel and an external
power amplifi er for 2-channel. In
this case, go to step 6.
PRE AMP
Select the PRE AMP setting to
use this unit as a preamplifi er
by connecting all speakers to an
external power amplifi er. You
can perform up to 11.2-channel
playback. In this case, go to step
7.
5
Use i to select “Assign Sp.”, and
use o p to select a speaker for audio
output assigned by “Amp Assign”.
S.BACK
Select the S.BACK setting to
output the assigned audio from
the surround back speakers.
F.HEIGHT
Select the F.HEIGHT setting to
output the assigned audio from
the front height speakers.
F.WIDE
Select the F.WIDE setting to
output the assigned audio from
the front wide speakers.
6
Use i to select “Ext. Amp”, and
use o p to select the PRE OUT
connector to which an external
power ampli er is connected.
Height
Select the Height setting to
connect an external power
amplifi er to the front height (FHL/
FHR) terminals of PRE OUT
connector for playback.
Front
Select the Front setting to connect
an external power amplifi er to the
front (FL/FR) terminals of PRE
OUT connector for playback.
7
Use i to select “Assign Sp.”, and use
o p to set whether or not to use the
speaker terminals for multizone.
None
Select the None setting when you
do not want to use the speaker
terminals for multizone.
ZONE2/3
Select the ZONE2/3 setting when
you want to use the speaker
terminals for multizone.
8
Press RETURN to exit the “Amp
Assign” setting.
9
Set up “Channel Select”
Use ui to select “Channel Select”,
and then press ENTER.
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
Amp Assign
RETURN
Auto Setup Start
Channel Select
STEP1 Preparation
Connect the speakers and place them according
to the recommen
Measuren the manual,
Set the following items
If necessary.
Enable skip of measuring unused channels to reduce time
Enter Cancel
Channel Select
Subwoofer Measure (1 spkr)
Measure subwoofer channel (1 speaker)
Enter
Cancel
Surround Back Measure (2 spkrs)
Front Height Measure
RETURN
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
Amp Assign
RETURN
Auto Setup Start
Channel Select
STEP1 Preparation
Connect the speakers and place them according
to the recommendations in the manual,
Set the following items
If necessary.
Enable skip of measuring unused channels to reduce time
Enter Cancel
10
Use ui to select a channel.
Front
Select for setting the front speakers
to be used. In this case, go to step
11.
• “Front” can be set when “Assign
Mode” is set to “Front B”.
Subwoofer
Select the number of subwoofers to
be used. In this case, go to step 12.
Surround
Back
Select the number of surround back
speakers to be used. In this case, go
to step 13.
• “Surround Back” cannot be set
when “Amp Assign” – “Assign
Mode” is set to “ZONE2/3” or
when “Assign Sp.” is set to
“S.BACK”.
Front
Height
Select for no front height speakers
to be used. In this case, go to step
14.
• “Front Height” cannot be set
when “Amp Assign” – “Assign
Mode” is set to “ZONE2/3”, “2CH
Bi-AMP” or when “Assign Sp.” is
set to “F.HEIGHT”.
Front Wide
Select for no front wide speakers to
be used. In this case, go to step 14.
• “Front Wide” cannot be set when
“Amp Assign” – “Assign Mode” is
set to “ZONE2/3”, “2CH Bi-AMP”
or when “Assign Sp.” is set to
“F.WIDE”.
11
Press o p to select a front speaker.
A
Select this to use front speaker A.
B
Select this to use front speaker B.
A+B
Select this to use front speakers A and B
simultaneously.
12
Use o p to set whether or not a
subwoofer channel is measured.
Measure
(2 spkrs)
Set for measuring two subwoofers
(multiple subwoofe calibration).
Measure
(1 spkr)
Set for measuring a subwoofer.
Skip
Set for no measuring of a subwoofer.
• When using two subwoofers, please select
“Measure (2 spkrs)”.
13
Use o p to set whether or not a
surround back channel is measured.
Measure
(2 spkrs)
Set for measuring two surround back
speakers.
Measure
(1 spkr)
Set for measuring a surround back
speaker.
Skip
Set for no measuring of a surround
back speaker.
14
Use o p to set whether or not front
height and front wide channels are
measured.
Measure
Set to measure the front height
speakers or front wide speakers.
Skip
Set when you do not want to measure
the front height speakers or front wide
speakers.
15
Press ENTER.
Proceed to page 9
STEP1 Preparation
step 6.
NOTE
After performing Audyssey
®
Auto Setup, do not
change the speaker connections or subwoofer
volume. In event of a change, perform Audyssey
Auto Setup again.
1.AVR4311CIEU_ENG_108.indd 64 2010/08/30 20:10:54