Filter
Top Products
9
Basic version Advanced version InformationSimple version
Set up speakers (Audyssey
®
Auto Setup)
STEP 1
Preparation
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confi rm the setting Return to previous menu
STEP 2
Detection & Measurement
(Main listening position)
STEP 3
Measurement
(2nd – 8th listening position)
7
The detected speakers are displayed.
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
RETURN
Next Measurement
Retry
STEP2 Speaker Detection Check
Front
Center
Subwoofer
Surround
Surround Back
Front Height
Yes
Yes
1spkr
Yes
2spkrs
No
Proceed to STEP 3 after checking speaker connection result
Enter Cancel
NOTE
If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.
8
Use ui to select “Next →
Measurement” and then press
ENTER.
• In STEP 3, you will perform measurements at
multiple positions (two to eight positions) other
than the main listening position.
• You can achieve a more effective correction of
distortion within the listening area by performing
measurements at multiple positions.
9
Move the setup microphone to
position 2, use ui to select
“Measure”, and then press ENTER.
The measurement of the second position
starts. Measurements can be made in up to
eight positions.
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
RETURN
Next Calculation
Measure
STEP3 Measurement(2nd-8th)
Please place the microphone at ear
height at 2nd Iistening position.
Start measurement. Output large test tone during measuring
Enter Cancel
If you want to omit measurements from the next
position onward, select “Next → Calculation”.
(Go to
STEP4 Calculation
)
10
Repeat step 9, measuring positions 3
to 8.
When measurement of position 8 is
completed, a “Measurements fi nished.”
message is displayed.
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
RETURN
Next Calculation
Proceed to STEP4 (Calculation)
Enter Cancel
Retry
STEP3 Measurement(2nd-8th)
Measurements finished.
NOTE
If “Caution” is displayed:
Go to “Error messages” (vpage 11), check
any related items, and perform the necessary
procedures.
When performing Audyssey Auto
Setup over again
Press ui to select “Retry”, and then press ENTER.
When measuring has stopped
Press RETURN, to the “Cancel auto setup?” prompt
is displayed.
Press o to select “Yes”, then press ENTER.
Setting up the speakers again
Repeat the operation from step 4 of
STEP1 Preparation
.
• In STEP 2, you will perform measurements at the
main listening position.
• This step automatically checks the speaker
confi guration and speaker size, and calculates the
channel level, distance, and crossover frequency.
It also corrects distortion in the listening area.
6
Select “Measure” and then press
ENTER.
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
RETURN
Measure
STEP2 Detection & Measurement (main)
Please place the microphone at ear
height at main Iistening position.
Start measurement. Output large test tone during measuring
Enter Cancel
q Measure the subwoofer level
• To stop measuring, select “Cancel” and then
press ENTER.
• When “Subwoofer” is set to “Skip” with
“Channel Select”, this measurement is not
taken, and the process proceeds to “w
Measure each speaker”.
w Measure each speaker
• Once the measurements in step q are
complete, the measurements in step w start
automatically.
• The measuring channel changes depending
on the setting of “Set up “Amp Assign””
(vpage63) and “Set up “Channel Select””
(vpage64).
• Measurement requires several minutes.
4
Connect the setup microphone to the
SETUP MIC jack of this unit.
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
Amp Assign
RETURN
Auto Setup Start
Channel Select
STEP1 Preparation
Connect the speakers and place them according
to the recommendations in the manual,
Set the following items
If necessary.
Start Auto Setup
Enter Cancel
When the setup microphone is
connected, the following screen is
displayed.
This screen provides the method for setting
up 7.1-channel playback using surround back
speakers. For the method of setting up speakers
other than the 7.1-channel system, select “Amp
Assign” and perform step 3 and 7 of “Set up
“Amp Assign”” (vpage63).
If unused channels are set with “Channel Select”,
measuring time can be shortened. Also, set
“Channel Select” to measure two subwoofers.
For setting, perform steps 9 to 14 of “Set up
“Channel Select”” (vpage64).
5
Use ui to select “Auto Setup Start”
and then press ENTER.
1.AVR4311CIEU_ENG_108.indd 9 2010/08/30 20:10:23