Denon AVP-A1HD Stereo Amplifier User Manual


 

Getting Started Connections Other Operations Multi-Zone Information Troubleshooting SpecificationsSetup
LFE
Adjust the low-frequency effects level (LFE).
[Variable range]
–10dB
~
0dB
Center Gain
Assign center channel signal to front left and right channels for wider
sound.
n In DTS NEO:X mode, “Cinema” or “Game” is selected.
[Variable range]
0.0
~
1.0
n In DTS NEO:X mode, “Music” is selected.
[Variable range]
0.0
~
0.3
~
1.0
Panorama
Assign front L/R signal also to surround channels, for wider sound.
[Selectable items]
ON
OFF
For proper playback of the different program sources, we recommend
setting to the values below.
• Dolby Digital sources: “0 dB”
• DTS movie sources: “0 dB”
• DTS music sources: “–10 dB”
Delay Time
Adjust delay time to control sound stage size.
[Variable range]
0ms
~
30ms
~
300ms
Effect
Switch effect signal for multi-surround speakers on and off.
[Selectable items]
ON
OFF
Effect Level
Adjust effect signal level.
[Variable range]
1
~
10
~
15
Room Size
Determine size of acoustic environment.
[Selectable items]
Small
Medium small
Medium
Medium large
Large
Set to a lower level if the positioning and sense of phase of the
surround signals seems unnatural.
NOTE
“Room Size” does not indicate the size of the room in which sources
are played.
Dimension
Shift sound image center to front or rear, to adjust playback balance.
[Variable range]
0
~
3
~
6
Center Width
Assign center channel signal to front left and right channels for wider
sound.
[Variable range]
0
~
3
~
7
This can be set when playing back a DTS NEO:X.
AFDM
Auto-select surround mode by source.
This function only works for software containing a special identification
signal.
If the software being played is recorded in Dolby Digital EX, it is played
in 6.1-channels. If not, it is played in 5.1-channels.
[Selectable items]
ON
OFF
Example : Playing Dolby Digital software (with EX flag)
• When “AFDM” is set to “ON”, the surround mode is automatically
set to the DOLBY D + PLgx C mode.
• To play in the DOLBY DIGITAL EX mode, set “AFDM” to “OFF” and
“SB CH Out” to “MTRX ON”.
Some Dolby Digital EX sources do not include EX flags. If the playback
mode does not switch automatically even when “AFDM” is set to
“ON”, set “SB CH Out” to “MTRX ON” or “PLgx CINEMA”.
SB CH Out (for Multi-channel sources)
Select playback mode for surround back channels.
[Selectable items]
ON
z1
MTRX ON
PL
II
x CINEMA
z2
PL
II
x MUSIC
z3
OFF
z1: Convert the 5.1-channel source of the DTS/DTS-HD input signals
to the 7.1-channel output recommended by DTS and then play.
This can be selected when playing the 5.1-channel source of DTS/
DTS-HD.
z2: This can be selected when “Surround Back” is set to “2spkrs”
at the GUI menu “Manual Setup” – “Speaker Setup” – “Speaker
Configuration” setting (vpage 23).
z3: This can be selected when “Surround Back” is set to “2spkrs”
or “1spkr” at the GUI menu “Manual Setup” – “Speaker Setup”
–“Speaker Configuration” setting.
SB CH Out (for 2-channel sources)
Determine whether to use surround back speakers.
[Selectable items]
ON
OFF
When using the surround back speaker, you can change the “SB
CH Out” setting by pressing the STANDARD button.