Yamaha RX-V2700 Stereo Receiver User Manual


 
102 En
GRAPHIC USER INTERFACE (GUI) SCREEN
Use the “V-RESET” in “ADVANCED SETUP” to set the
parameters in “Manual Setup (Video)” (except “Short Message”
and “On Screen”) to the factory presets (see page 136).
Conversion (Video conversion)
Use this feature to activate or deactivate the video
conversion as well as the HDMI up-conversion of the
analog video signals input at the composite video, S-video
and component video jacks.
Choices: Off, On
Select “Off” to deactivate the video conversion as well
as the HDMI up-conversion of the analog video
signals.
Select “On” to activate the video conversion as well as
the HDMI up-conversion of the analog video signals.
This unit does not convert 480 line video signals and 576 line
video signals interchangeably.
The analog component video signals with 480i (NTSC)/576i
(PAL) of resolution are converted to the s-video or composite
video signals and output at the S VIDEO MONITOR OUT and
VIDEO MONITOR OUT jacks.
The converted video signals are only output at the MONITOR
OUT jacks. When recording a video source, you must make the
same type of video connections between each component.
When composite video or S-video signals from a VCR are
converted to component video signals, the picture quality may
suffer depending on your VCR.
Even when “Conversion” is set to “On”, HDMI digital signals
are not converted to analog video signals.
If “Conversion” is set to “Off”, the “Component I/P” and
“HDMI Up-Scaling” features are deactivated.
Set “Conversion” to “On” to display the short message display.
Unconventional signals input at the composite video or S-video
jacks cannot be converted or may be output abnormally. In such
cases, set “Conversion” to “Off”.
When non-standard video signals (such as video signals from a
game console) are input, this unit may not convert the signals
even if you “Conversion” to “On”.
When the analog component video signals with 480p of
resolution are input at the COMPONENT VIDEO jacks and the
video monitor is connected to the VIDEO MONITOR OUT or
S VIDEO MONITOR OUT jack of this unit, the GUI screen is
not displayed on the video monitor.
Component I/P
(Component interlace/progressive
conversion)
Use this feature to activate or deactivate the analog
interlace/progressive conversion of the analog video
signals input at the composite video, S-video and
component video jacks so that the analog video signals
deinterlaced from 480i (NTSC)/576i (PAL) to 480p/576p
are output at the COMPONENT MONITOR OUT jacks.
Choices: Off, On
Select “On” to activate the analog interlace/progressive
up-conversion of the analog video signals.
Select “Off” to deactivate the analog interlace/
progressive up-conversion of the analog video signals.
This menu item is not available and hence not visible in the GUI
screen if “Conversion” is set to “Off”.
If your video monitor does not support analog video signals
with 480p/576p of resolution, the GUI screen may not be
displayed on your video monitor when “Component I/P” is set
to “On”. Use “V-RESET” in “ADVANCED SETUP” to set the
“Component I/P” parameter to the factory preset setting (see
page 136).
HDMI Up-Scaling (HDMI up-scaling)
Use this feature to activate or deactivate the HDMI up-
conversion of the analog video signals input at the
composite video, S-video and component video jacks so
that the up-scaled analog video signals are output at the
HDMI OUT jack.
This unit up-scales the analog video signals as follows:
480i (NTSC)/576i (PAL) 480p/576p, 1080i or
720p
480p/576p 1080i or 720p
Choices: Through, 480p (or 576p), 1080i, 720p
Select “Through” not to up-scale any analog video
signals.
Select “480p” (or “576p”), “1080i” or “720p” to up-
scale analog video signals to 480p or 576p, 1080i or
720p of resolution.
Note
Notes
Off
On
Conversion
Component I/P
HDMI Up-Scaling
Notes
On
Off
Component I/P
HDMI Up-Scaling
HDMI Aspect
Conversion
Through
1080i
720p
480p
HDMI Up-Scaling
HDMI Aspect
Short Message
Component I/P
Conversion