Sherwood P-965 Stereo Amplifier User Manual


 
44
ENGLISH
After you have installed this unit and connected all the components, you first perform the speaker setup settings for the optimum sound acoustics
according to your environment and speaker layout.
Even when you change speakers, speaker positions, or the layout of your listening environment, you should perform the speaker setup settings, too.
When performing the AUTO SPEAKER SETUP procedure, you need not perform the SPEAKER CONFIGURATION, SPEAKER DISTANCE and
CH LEVEL SETUP procedures.
Depending on your speaker type, you can select one of these following speaker types.
Yes/No : Select the desired depending on whether a subwoofer is connected or not.
Large : Select this when connecting speakers that can fully reproduce sounds below
crossover frequency.
Small : Select this when connecting speakers that cannot fully reproduce sounds below
crossover frequency.When this is selected, sounds below crossover frequency are
sent to the subwoofer.
None : Select this when no speakers are connected. When this is selected, sounds are sent
to the speakers which are not set to None.
2CH/1CH : Select the desired depending on the number of surround back speakers.
• Each time these buttons are pressed, “ ” and “ ” are
moved to the corresponding speaker mode.
Notes :
• When speakers are set to “Small”, you should set the CROSSOVER FREQUENCY correctly according to their low
frequency playback capacity. (Refer to “When selecting the CROSSOVER FREQUENCY” on page 48.)
• When “FRONT’ is set to “Small”, “SUBWOOFER” is automatically set to “Yes”, and when “SUBWOOFER” is set to
“No”, “FRONT” is automatically set to “Large”.
• When “FRONT” is set to “Small”, “CENTER”, “SURROUND” and “SURR. BACK” cannot be set to “Large”.
• When “SURROUND” is set to “None”, “S/B CH” is automatically set to “None”.
STANDBY
POWER ON
MAIN
PAGE
FAV
MUTE
CH.
SET
VOL
RETURN
DISP
MI
OSD/MENU
1
STEREO
CH/
ADJUST
2
3
4
5
6
7
8
9
0
ENT
M2
M3
DSP
DECODE
DSP
STANDBY
POWER ON
MAIN
PAGE
FAV
MUTE
CH.
SET
VOL
RETURN
DISP
MI
OSD/MENU
1
STEREO
CH/
ADJUST
2
3
4
5
6
7
8
9
0
ENT
M2
M3
DSP
DECODE
DSP
RNC-510
SPEAKER SETUP
RETURN:Back ENTER:Select
SPEAKER CONFIGURATION
SPEAKER DI STANCE
VIRTUAL SPEAKER SETUP
SUBWOOFER : ACT I VE
SUBWOOFER MODE : LFE
CROSSOVER FREQ. : 80Hz
AUTO SPEAKER SETUP
, :Move
To select the sizes of the speakers that are connected.
To enter the distance between the listening position and each speaker to set
the delay time automatically for the optimum surround playback.
To adjust the Dolby Virtual Speaker setting modes as desired.
To select the type of the subwoofer that is connected.
To select the desired subwoofer mode
To select the desired crossover frequency.
To set the speaker setup and channel level setup automatically.
SPEAKER CONFIGURATION
SUBWOOFER :
FRONT :
CENTER :
SURRROUND :
S / B CH :
SURR . BACK :
RETURN:Back , :Select
Large
Large
Large
Large
Yes
2CH
STANDBY
POWER ON
MAIN
PAGE
FAV
MUTE
CH.
SET
VOL
RETURN
DISP
MI
OSD/MENU
1
STEREO
CH/
ADJUST
2
3
4
5
6
7
8
9
0
ENT
M2
M3
DSP
DECODE
DSP
RNC-510
Press the CURSOR UP( )/DOWN( ) buttons to select the SPEAKER CONFIGURATION, then press
the ENTER button.
1
Press the CURSOR UP( )/DOWN( ) buttons to select the desired speaker.
2
Press the CURSOR LEFT( )/RIGHT( ) buttons to select the desired mode.
3
SETTING THE SPEAKER SETUP
When selecting the SPEAKER CONFIGURATION