Filter
Top Products
103
12
The System Setup and Other Setup menus
! If an update file is provided on the Pioneer website, download it onto your computer. When downloading an
update file from the Pioneer website onto your computer, the file will be in ZIP format. Unzip the ZIP file before
saving it on the USB memory device. If there are any old downloaded files or downloaded files for other models
on the USB memory device, delete them.
Important
! DO NOT unplug the power cord during updating.
! When updating via the Internet, do not disconnect the LAN cable. When updating via a USB memory device,
do not disconnect the USB memory device.
! If updating is interrupted before it is completed, start updating over from the beginning.
! The receiver’s settings may be reset when the software is updated. Information on the models for which the
settings are reset is provided on the Pioneer website. Check the website before updating.
1 Select ‘Software Update’ from the Other Setup menu.
2 Select the update procedure.
! Update via Internet – The receiver checks whether updatable software is available via the Internet.
! Update via USB Memory – The receiver checks whether the USB memory device inserted into the USB port
on the receiver’s front panel contains updatable software.
“Accessing” is displayed and the update file is checked. Wait a while.
3 Check on the screen whether or not an update file was found.
If “New version found.” is displayed, the update file has been found. The version number and updating time are
displayed.
If “This is the latest version. There is no need to update.” is displayed, no update file has been found.
4 To update, select OK.
The updating screen appears and updating is performed.
! The power turns off automatically once updating is completed.
Software Update messages
Status messages Descriptions
FILE ERROR
Try disconnecting then reconnecting the USB device or storing the update file again. If the error still
occurs, try using a different USB memory device.
No update file was found on the USB memory device. Store the file in the USB memory device’s root
directory.
UPDATE ERROR 1 to
UPDATE ERROR 7
Turn the receiver’s power off, then turn it back on and try updating the software again.
Update via USB
If this message flashes, updating has failed. Update via a USB memory device. Put the update file on a
USB memory device and connect the device to the USB port. When the file is found, software updating
starts automatically.
UE11
Updating has failed. Use the same procedure to update the software again.
UE22
UE33
ZONE Setup
The volume setting and tone for the sub zones that can be used with this receiver can be changed and adjusted
here.
CAUTION
! Note that when Volume Level is set to 0 dB Fixed, the audio output from the AUDIO ZONE 2 OUT terminals
is set to the maximum. Also, depending on the volume setting on the connected amplifier, large volumes may
be produced even when Volume Level is set to –40 dB Fixed.
1 Select ‘ZONE Setup’ from the Other Setup menu.
2 Select ‘ZONE 2’ or ‘ZONE 3’, then press ENTER.
3 Select the Volume Level setting you want.
When making multi-zone connections using the AUDIO ZONE 2 OUT or AUDIO ZONE 3 OUT terminals and per-
forming playback in Zone 2 or Zone3, you can set whether to adjust the Zone 2 or Zone3 volume on the receiver or
to fix it to a specific volume (–40 dB Fixed or 0 dB Fixed). This is set to Variable upon shipment from the factory,
allowing the volume to be adjusted on the receiver. If you would like to adjust the volume from the connected
amplifier, make the setting below.
For ZONE 2, this setting is not possible if multi-zone settings have been made using the speaker terminals and
Speaker System is set to 7.1ch + ZONE 2. In this case, adjust the volume for the sub zones on the receiver.
! Variable (default) – The Zone 2/Zone3 volume is adjusted from the receiver.
! –40 dB Fixed/0 dB Fixed – The Zone 2/Zone 3 volume level output from the receiver is fixed to the value set
here.
4 Select the Power ON Level setting you want.
The sub zone volume is set to the volume selected here when the sub zone is turned on using the multi-zone func-
tion. Zones 2 and 3 can be set separately.
When Volume Level is set to –40 dB Fixed or 0 dB Fixed, the volume is fixed to that level, so the volume cannot
be set here.
! LAST (default) – When MULTI-ZONE is turned on, the volume is set to the level set the last time you were
listening to that zone.
! “---” – When MULTI-ZONE is turned on, the volume for that zone is set to the minimum.
! –80.0dB to 0dB – When MULTI-ZONE is turned on, the volume is set to the level set here. The volume can be
set up to the value set at Volume Limit below.
5 Select the Volume Limit setting you want.
The maximum volume for the zone selected in step 2 can be set.
! OFF (default) – The maximum volume is not limited.
! –20.0dB/–10.0dB – The maximum volume is limited to the value set here.
6 Select the Mute Level setting you want.
The mute level for the zone selected in step 2 can be set.
This sets how much the volume is to be turned down when MUTE is pressed.
! FULL (default) – No sound.
! –40.0dB/–20.0dB – The volume will be turned down to the level specified here.
7 Adjust Lch Level and Rch Level.
The channel level for the zone selected in step 2 can be set.
The level can be adjusted between –12.0dB and +12.0dB, in 1 dB steps.
8 Select the HPF (High Pass Filter) setting you want.
This can only be set when ZONE 2 is selected in step 2.