Filter
Top Products
43
Model 1070 7.1 Channel Surround Sound Receiver
Owner’s Manual
Remote Control Setup and Operation
Programming TV/VCR Control
The Model 1070 can control TV/VCR combo units, but the procedure is some-
what different than entering codes to control other components. As with other
components, you must enter a four-digit code. Codes for many TV/VCR brands
are provided in the following pages. More than one setup code number may work
with your device. You should test the functions for each of the code numbers
that work with your device to determine the best one for your particular unit.
If you want to control TV functions besides power on/off, you may need to enter
a separate TV code, as described below.
To program TV/VCR control:
1. Turn on the TV/VCR, either manually or with its original remote
control, and insert a video cassette.
2. Find the four-digit code for your TV/VCR from the tables on pages
44 to 49. Your TV/VCR may have a separate TV code listed. If so,
be sure to note both codes.
3. On the Model 1070 remote, press VCR.
4.
Press and hold SETUP until the red LED blinks twice, then release SETUP.
5. Enter the first four-digit code for your component.
If the code entry is performed correctly, the LED will blink twice. If it
does not, then repeat steps 3, 4, and 5, using the same four-digit code.
6. Aim the remote at the TV/VCR and press PWR once. The TV/VCR
should turn off. If it does not respond, repeat steps 3, 4, and 5, trying
each code for your brand until you find one that works. If it still does
not work, try searching for the code (see Searching For Your Code).
7. If your component has a separate TV code listed, press TV on the
Model 1070 remote control.
The LED will blink twice.
8. Enter the four-digit TV code for your TV/VCR combo.
If the code is entered correctly, the LED will blink twice. If it does not,
then repeat steps 7 and 8 using the same four-digit code.
Searching for Your Code
If your device does not respond to the remote after you have tried all codes
listed for your brand, or if your brand is not listed at all, try searching for your
code.
To search for a code for your component:
1. Press the Device Control Selector button on the Model 1070
remote that corresponds to the device you want to control.
You can choose CBL, AUX, VCR, TV, SAT, CD, or AMP.
2. Press and hold SETUP until the red LED on the remote blinks twice,
then release SETUP.
3. Enter 991.
The LED will blink twice.
4.
Aim the remote control at the component and slowly alternate between
pressing PWR and the button for the device you pushed in step 1
.
5. Stop when the TV turns off.
6. Press SETUP once.
7. To search for the codes of your other components, repeat the
process, using the appropriate button for the new device in steps
1 and 4.
Checking the Codes
If you have set up the Model 1070 remote by searching for the codes, for future
reference, you may wish to find out which four-digit code is operating your
equipment.
To find the four-digit code for a device:
1. On the Model 1070 remote, press the button near the top of the
remote for the type of device you want to control.
2. Press and hold SETUP until the red LED on the remote blinks twice,
then release SETUP.
3. Enter 990.
The LED will blink twice.
4. To view the code for the first digit, press 1.
After three seconds, the LED will blink to indicate the first code number
(i.e., 3 blinks = 3). Count the blinks and write down the number.
5. Repeat steps 1-4 for each of the other three digits.
Press
2
for the second digit,
3
for the third, and
4
for the fourth. Count
the blinks and write down the numbers.
6. To check for the codes of your other components, repeat steps 1
through 5, but substitute the appropriate key in step 1 for the new
component you are checking.
Re-Assigning Device Buttons
If you wish to control a second device of a type already programmed into the
Model 1070 remote (i.e., if you want to use two DVD players), you will need to
re-assign an unused device button (CBL, AUX, VCR, TV, SAT, CD, or AMP) to
operate the second device.
To reassign an unused device button:
1. On the Model 1070 remote, press and hold SETUP until the LED
blinks twice, then release SETUP.
2. Enter 992.
The LED will blink twice.
3. Press the button for the device already programmed (i.e., CBL),
then press the button for the unused device (i.e., TV).
The LED will blink twice.
4. The button for the unused device is now ready to be programmed
for the second component. See Setup Using Preprogrammed
Codes.
Volume Control Punch-Through
You can program the Model 1070 remote so that the VOLUME UP, VOLUME
DOWN, and MUTE buttons on the remote will control those functions on the
Model 1070 even when the remote is set to control another device.
To set volume control punch-through:
1. On the Model 1070 remote, press and hold SETUP until the LED
blinks twice, then release SETUP.
2. Enter 993.
3. Press the TNR key on the Model 1070 remote.
The LED will blink twice.