Filter
Top Products
45
Using the other remote controller functions with the supplied remote controller
The remote controller supplied with the TX-DS656
can learn functions available with other compo-
nent's remote controllers.
The control codes for Onkyo cassette tape decks and CD players are
already available with the supplied remote controller.
SENDING/LEARNED indicator
This indicator lights when the remote controller is transmitting a control
command or learning other controller's functions. If the indicator does not
light, replace the batteries.
A/B-SUBROOM/LEARN switch
A: Select this position to use the remote controller in the main
room.
B-SUBROOM: Select this position to use the remote controller in the
sub-room.
LEARN: Select this position to have the supplied remote
controller learn another remote controller's functions.
PROGRAMMABLE AREA TV/VIDEO buttons
Use these buttons to have the supplied remote controller learn another
remote controller's function.
For TV: Power ON/OFF (POWER) and Channel selection (
a
CH
s)
.
For VDP: Power ON/OFF (POWER), Playback (
s
), and Stop (e)
For VCR: Playback (
s
), Stop (e), Rewind (
d
), and Fast
Forward (
f
)
MUTING
POWER
SLEEP
DVD VIDEO-1
VIDEO-2
TAPE-1 TUNER PHONO C D
SOURCE SELECTOR
DVD
DISC
PAUSE
/
STEP
TONE
TEST
MODE
SUR
VIDEO-3
M
TI-CHUL
INPUT
TAPE-2
POWER
POWER
TAPEC D
TV/
VCR
VOLUME
TUNER
/
REMOTE
SPEAKER
CURSOR
ENTER
REMOTE CONTROLLER
CH SEL
SENDING/
LEARN
SUBROOM
C H
AB
LEVEL
DIMMER
PRESETGROUP
LEARNED
PROGRAMMABLE AREA TV
VIDEO
/
SUBTITLE
ON
/
OFF
RC-373M
VOLUME
PROGRAMMABLE
AREA TV/VIDEO
buttons
A/B-SUBROOM/
LEARN switch
SENDING/
LEARNED
indicator
Learning new control codes
1. Set the A/B-SUBROOM/LEARN selector switch to LEARN.
2. Place the head of your existing remote controller 2-4 inches (5-10 cm)
from the head of this remote controller, laying both units on a table or
another flat surface.
3. Press a button in the PROGRAMMABLE AREA of this remote
controller to which you want to transfer the code.
The SENDING/LEARNED indicator lights.
4.
Hold down the button for the function you want to transfer on the other
remote controller until the SENDING/LEARNED indicator turns off.
5. Repeat steps 3 and 4 until all the required function are trans-
ferred to the supplied remote controller.
6. Set the A/B-SUB ROOM/LEARN selector switch back to A.
Note:
•
Some remote controllers use a single button to change codes, with the code
changing each time the button is pressed. If you are using this type of
controller, perform "learn" operations for each function individually, one
function to one button on this remote controller.
•
This remote controller transmits codes using infrared rays and can memorize
the codes of other remote controllers that also use an infrared system; however,
depending on the system, there may be some rare occasions when memoriza-
tion is not possible.
Changing the learned commands
Perform the whole procedure described in "Learning new control
codes". The existing commands on the supplied remote controller are
replaced with the newly learned commands.
1
LEARN
SUBROOM
AB
Switch to LEARN
1,6
3
4
2
5 to 10 cm
(2 to 4 inches)
To erase all the learned commands
1. Set the A/B-SUB ROOM/LEARN selector switch to LEARN.
2. While pressing the POWER button, hold down the VOLUME
u button until the SENDING/LEARNED indicator turns off.
All the commands stored in programmable area have been erased.
1
LEARN
SUBROOM
AB
Switch to LEARN
POWER
VOLUME
2