Filter
Top Products
26
EN
Preparing for playback
! Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select the appropriate BS/SW amp setting.
1 "BS/SW BS":
Select this setting when a surround back speaker is
connected to the SURR BACK/SW terminals. In this
case, the subwoofer signal will be output from the PRE
OUT SUBWOOFER jack.
2 "BS/SW SW":
Select when the subwoofer speaker is connected to the
SURR BACK/SW terminals. In this case, the surround
back signals will be output from the PRE OUT SUR-
ROUND BACK jacks.
3 "BS/SW OFF":
Select when no speaker is connected to the SURR
BACK/SW terminals. In this case, the subwoofer signal
will be output from the PRE OUT SUBWOOFER jack and
the surround back signals will be output from the PRE
OUT SURROUND BACK jacks.
÷ If "BS/SW BS" is selected, only one surround back
speaker can be connected to the receiver.
÷ If "BS/SW SW" or "BS/SW OFF" is selected, two sur-
round back speakers can be connected to the PRE OUT
SURROUND BACK jacks through an external power
amplifier. ^
@ Use the MULTI CONTROL # (or the Multi # key)
to accept the setting.
÷ The subwoofer re-mix setting indication "REMIX" appears.
# Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select the appropriate subwoofer re-mix setting.
If "REMIX ON" is selected as the subwoofer re-mix setting,
the low frequencies are enhanced by adding the low fre-
quencies of other channels to the subwoofer channel or
adding the low frequencies of the subwoofer to other
channels depending on the speaker setup.
1 "REMIX ON" :
Subwoofer re-mix setting mode to the receiver is ON.
2 "REMIX OFF" :
Subwoofer re-mix setting mode to the receiver is OFF.
÷ The initial setting is "REMIX ON".
÷ The subwoofer re-mix setting is possible only when the
subwoofer setting is "SUBW ON" and the front speaker
setting is "FRNT LRG".
$ Press ENTER (or the Enter key). If your selection is
correct, press MULTI CONTROL % / fi (or the Multi
% / fi key) to select "OK".
Press the ENTER (or the Enter key) again to return to
the main setup displays.
÷ Select "CANCEL" and press the ENTER (or the Enter
key) to return to the status before setup.
÷ In steps 6 and 7, indications appear only for the se-
lected channels of the speakers that require adjusting.
6
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The volume
levels from each speaker should be the same.
1 Use the MULTI CONTROL @ / # (or the Multi @ / # keys)
to select "SP LEVEL" on setup displays, and press the
ENTER (or the Enter key).
2 Use the MULTI CONTROL @ / # (or the Multi @ / # keys)
to select "AUTO", "MANUAL" or "OFF".
1 "AUTO": Select this setting to adjust the speaker volume
levels using the test tone. The test tone will be output from
every speaker channel in automatic sequence.
2 "MANUAL": Select to select the speaker channel to
output the test tone using MULTI CONTROL@ / #
(or the Multi @ / # key).
3 "OFF": Select to adjust the speaker volume levels
using the current output signals. The speaker chan-
nel to output the output signal can be selected using
MULTI CONTROL@ / # (or the Multi @ / # key).
4 "EXIT": Press the ENTER (or the Enter key) again to
return to the main setup displays.
When "AUTO" or "MANUAL" is selected and ENTER (or the
Enter key) is pressed again, the test tone output will start.
Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to adjust the volume level of the test tone output from
the speaker channel to be adjusted.
For
"
AUTO
"
selection, the first test tone is heard from
the front left speaker for 2 seconds. The next test tone
is heard from the speakers in the following sequence
for 2 seconds each.
When the "BS/SW BS" has been selected :
When the "BS/SW SW" or "BS/SW OFF" has been selected:
The channel indication blinks while the test tone is being output.
L 1 ) dB
÷ If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are
also changed. w
÷ If the speaker setting selects are OFF, the speaker level
settings are reset.
When "MANUAL" or "OFF" is selected, press MULTI
CONTROL @/# (or the Multi @/# key) to select the
speaker channel and then press MULTI CONTROL %/fi
(or the Multi %/fi key) to adjust the speaker volume level.
3 Press the ENTER (or the Enter key) again to return to
the main setup displays.
÷ The test tone is turned off and return to the main setup
displays.
*5462/20-36/EN 04.4.13, 8:01 PM26