Filter
Top Products
25
EN
Preparing for playback
Continued to next page
5
Select a speaker system.
1 Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select the appropriate subwoofer setting.
1 "SUBW ON" :
When a subwoofer is connected.
2 "SUBW OFF" :
When no subwoofer is connected.
÷ The initial setting is "SUBW ON".
÷ When "SUBW OFF" is selected and the selection is established
by pressing MULTI CONTROL # (or the Multi # key) in step 2
below, the front speakers are set automatically to "FRNT LRG"
and the procedure jumps to step 5.
2 Use the MULTI CONTROL # (or the Multi # key)
to accept the setting.
÷ The front speakers setting indication "FRNT" appears.
FRNT LRG
3 Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select the appropriate front speakers setting.
1 "FRNT LRG" :
Large front speakers are connected to the receiver.
2 "FRNT NML" :
Average size front speakers are connected to the
receiver.
÷ When the subwoofer setting is "SUBW ON", front speak-
ers setting is "FRNT LRG" and a stereo source is played,
the low frequencies may be reproduced through the
front speakers and no audio output fro the subwoofer in
certain listen modes. In this case, set the subwoofer re-
mix setting in step # to "REMIX ON" to output the low
frequencies from the subwoofer.
4 Use the MULTI CONTROL # (or the Multi # key)
to accept the setting.
÷ The center speaker setting indication "CNTR" appears.
5 Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select the appropriate center speaker setting.
If you selected "FRNT LRG" as the front speakers setting:
1 "CNTR LRG" :
A large center speaker is connected to the receiver.
2 "CNTR NML" :
An average size center speaker is connected to the
receiver.
3 "CNTR OFF" :
When no center speaker is connected.
If you selected "FRNT NML" as the front speakers setting:
1 "CNTR NML" :
Average size front speakers are connected to the
receiver.
2 "CNTR OFF" :
When no center speaker is connected.
6 Use the MULTI CONTROL # (or the Multi # key)
to accept the setting.
÷ The surround speaker setting indication "SURR" appears.
7 Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select the appropriate surround speaker setting.
1 "SURR LRG" :
Large surround speakers are connected to the receiver.
2 "SURR NML" :
Average size surround speakers are connected to the
receiver.
3 "SURR OFF" :
When no surround speakers are connected.
÷ When "SURR OFF" is selected and the selection is estab-
lished by pressing MULTI CONTROL # in step 8 below, the
procedure jumps to step #. However, if the subwoofer
setting is "SUBW OFF", the procedure jumps to step $ so
that you can complete the speaker setup and proceed to the
speaker volume level adjustment in step 6.
8 Use the MULTI CONTROL # (or Multi # key) to ac-
cept the setting.
÷ The surround back speaker setting indication "BS" appears.
9 Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select appropriate surround back speaker setting.
If you selected "SURR LRG" as the surround speaker setting :
1 "BS LRG" :
Large surround back speaker is connected to the re-
ceiver.
2 "BS NML" :
Average size surround back speaker is connected to the
receiver.
3 "BS OFF" :
When no surround back speakers is connected.
Bs LRG
If you selected "SURR NML" as the surround speaker setting :
1 "BS NML" :
Average size surround back speaker is connected to the
receiver.
2 "BS OFF" :
When no surround back speakers is connected.
0 Use the MULTI CONTROL # (or the Multi # key)
to accept the setting.
÷ The surround back speaker and subwoofer setting mode
indication "BS/SW" appears.
*5462/20-36/EN 04.4.13, 8:01 PM25