Filter
Top Products
56
Activating the Surround Modes
For the Surround modes, Parametric Equalizer adjustments done on
the Adjustment menu also take effect for the activated speaker
channels.
• Available Surround modes vary depending on the received signal
and the current speaker settings. For details, see “Surround and
THX Modes Applicable to the Various Software” on pages 53 and
54.
1. Select and play any source other than “DVD
MULTI” and “EXT 7.1CH.”
• Surround modes are not applicable to “DVD MULTI” and
“EXT 7.1CH.”
2. Press SURROUND to activate the Surround
mode.
• For multi-channel digital software (except 2-channel and
Dual Mono software), either “DOLBY DIGITAL” or “DTS
SURROUND” is activated.
– If the 7.1-channel reproduction (EX/ES/7.1) mode has been
set to “AUTO” or “ON,” one of the 7.1-channel reproduction
modes will be activated.
• For analog sources and digital 2-channel software, you can
select one of the following Surround modes. Each time you
press SURROUND, Surround modes change as follows:
• For Dual Mono software, speaker output channel changes to
the center speaker if it is connected and activated.
(You can select the channel you listen to. See page 42.)
Notes:
• While listening with the headphones, “3D HEADPHONE” will
appear on the display. (The DSP and HEADPHONE indicators
will light up.)
• If the THX mode or DSP mode is in use, it will be canceled
when you turn on the Surround mode.
To adjust the speaker output level using the remote control,
follow the procedure below.
• When Analog Direct is in use, you cannot adjust the speaker
output levels without emitting the test tone (see page 39).
From the remote control ONLY:
1. Press SOUND.
The 10 keys are activated for sound adjustments.
2. Select the speaker you want to adjust.
The selected speaker name appears on the
remote’s display for a while.
• To select the left front speaker, press
FRONT•L.
• To select the center speaker, press CENTER.
• To select the right front speaker, press
FRONT•R.
• To select the right surround speaker, press
SURR•R.
• To select the right surround back speaker, press
SURR BK•R.
• To select the left surround back speaker, press
SURR BK•L.
• To select the left surround speaker, press SURR•L.
• To select the subwoofer, press SUBWFR.
3. Press LEVEL +/– to adjust the speaker
output levels.
The speaker name selected in the above step
and its level appear on the unit’s display.
• You can adjust the levels within the range of
–10 dB to +10 dB.
4. Repeat steps 2 and 3 to adjust the other speaker output
levels.
To cancel the Surround mode
Press SURR/DSP OFF.
“SURROUND OFF” appears on the display.
On the unit
(inside the front door)
SURROUND
SURROUND
From the remote control
dB
L
ANALOG
SPEAKERS
VOLUME
1
SUBWFR
R
PL
NEO:6 CINEMANEO:6 MUSIC
PL
II
MOVIE PL
II
MUSIC PRO LOGIC
dB
L
DGTL AUTO
DIGITAL
SPEAKERS
VOLUME
1
SUBWFR
C R
LFE
RSLS
Ex. When “DOLBY DIGITAL” is activated.
dB
L
DGTL AUTO
DUAL
DIGITAL
SPEAKERS
VOLUME
1
SUBWFR
R
SOUND
EFFECT
LIVENESS
FM MODE
RETURN
100
+
123
456
7
/P
89
10
+
100
100
+
9
+
10
SURR/DSP
OFF
SURR/DSP
OFF
From the remote control
On the unit
(inside the front door)