Filter
Top Products
22
Zone 1 (Main Room) Operations
This section explains only the operations commonly used when you play any sound source in Zone 1 (main room).
See pages 29 to 32 for the Zone 2 (sub-room) operations.
• Before performing Zone 1 operations, it is recommended to finish the basic settings on pages 35 to 44.
IMPORTANT:
Check the following before or while using the buttons and controls.
For Zone 1 operations:
The ZONE 1 ON/OFF lamp on the unit is lit.
• When using the unit:
–“ZONE 2” is not shown in the main display.
–Press DOOR DOWN to use the buttons inside the
front door.
To close the front door, press DOOR UP.
• When using the remote control:
–Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to “ZONE 1.”
–Check the indication shown on the remote’s display when you
press a button—this indicates the remote control operation mode
together with multi-room operation mode (either ZONE 1 or
ZONE 2) for a while.
The last Zone 1 source is activated.
L
ANALOG
SPEAKERS
VOLUME
1
SUBWFR
R
dB
dB
The volume
level appears.
STANDBY
ON
DOOR
DOWN
Ex.When you press FM/AM with ZONE 1/ZONE 2
(LEARN/TRANSMIT) selector set to “ZONE 1.”
The last Zone 1 source is activated.
L
ANALOG
SPEAKERS
VOLUME
1
SUBWFR
R
dB
dB
The last Surround/THX/DSP mode
appears.
The volume
level appears.
ZONE 2
TRANSMITLEARN
ZONE 1
ON/OFF ON/OFF
STANDBY/ON STANDBY/ON
STANDBY
TV/CATV/DBS
VCR 1
ON
ZONE 2
TRANSMITLEARN
ZONE 1
ZONE 2
ZONE 1
ZONE 1
STANDBY/ON
STANDBY
ZONE 1
ON/OFF
Turning the Power On and Off (Standby)
On the unit:
To turn on the power, press (STANDBY/ON).
The STANDBY lamp goes off, and the ZONE 1 ON/OFF lamp
lights up. The front door moves down (so that the source selecting
buttons appear).
The currently selected speakers 1 and/or 2 indicator(s) also light(s)
up on the display.
• If neither speakers 1 nor 2 indicator is lit on the display, see
“Activating the Zone 1 Front Speakers” on page 25.
STANDBY/ON
STANDBY
To turn off the power (into standby mode),
press
(STANDBY/ON) again.
The STANDBY lamp lights up, and the front
door automatically closes. (The ZONE 1 ON/
OFF and/or ZONE 2 ON/OFF lamp goes off.)
• A small amount of power is consumed in standby mode. To turn
the power off completely, unplug the AC power cord.
From the remote control:
To turn on the power, press
AUDIO
(ON).
The STANDBY lamp goes off, and the ZONE 1
ON/OFF lamp on the unit lights up.
The front door moves down (so that the source selecting buttons
appear).
The currently selected speakers 1 and/or 2 indicator(s) also light(s)
up on the display.
• If neither speakers 1 nor 2 indicator is lit on the display, see
“Activating the Zone 1 Front Speakers” on page 25.
To turn off the power (into standby mode),
press AUDIO
(STANDBY).
The STANDBY lamp lights up, and the front
door automatically closes. (The ZONE 1 ON/
OFF and/or ZONE 2 ON/OFF lamp on the unit
goes off.)
Notes:
• Before you turn off the receiver in Zone 1, make sure that no one is
listening to any source in Zone 2 (the ZONE 2 ON/OFF lamp is lit
on the display) since the Zone 2 sound will also be turned off
unexpectedly.
• If you have turned off the receiver with the volume level set at more
than level “–35 dB,” the volume level will be automatically set at
level “–35 dB” next time you turn on the receiver.
When you turn on the TV connected to the TV SOUND/DBS
jacks on the rear
This receiver automatically turns on and selects “TV” as the Zone 1
source about 5 seconds after you turn on the TV. (If you change the
source name from “TV” to “DBS,” the receiver will not turn on
along with the TV. See “Changing the Source Name” on page 27.)
The last Surround/THX/DSP
mode appears.
STANDBY
ON