Filter
Top Products
62
English
Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control
signals for JVC components are preset in the remote control.
IMPORTANT:
To operate JVC’s audio components using this remote control:
• You need to connect JVC audio components through the COMPU LINK-3
(SYNCHRO) jacks (see page 54) in addition to the connections using cables
with RCA pin plugs (see page 14).
• Aim the remote control directly at the remote sensor on the receiver.
Tuner
After pressing FM/AM (with the remote control mode selector
set to “AUDIO/TV/VCR”), you can perform the following
operations:
FM/AM: Alternates between FM and AM.
1 — 10, +10: Selects a preset channel number directly.
For channel number 5, press 5. For
channel number 15, press +10, then 5.
For channel number 20, press +10, then
10.
TUNING UP/TUNING DOWN:
Tunes into stations.
FM MODE/MUTE: Changes the FM reception mode.
Sound control section (Amplifier)
You can always perform the following operations (with the
remote control mode selector set to “AUDIO/TV/VCR”):
SEA MODE: Changes the SEA modes.
SURROUND MODE: Changes the DSP modes.
After pressing SOUND CONTROL (with the remote control
mode selector set to “AUDIO/TV/VCR”), you can perform the
following operations:
CNTR +/–: Adjusts the center speaker output level for the Surround/DVD
MULTI playback modes.
REAR•(L) +/–: Adjusts the left/right rear speaker output level for the DSP
modes.
Adjusts the left rear speaker output level for the DVD MULTI
playback mode.
(REAR•R) +/–: Adjusts the right rear speaker output level for the DVD MULTI
playback mode.
DELAY: Selects the delay time of the rear speaker sound.
EFFECT: Selects the effect level for the DSP modes.
TEST: Turns on or off the test tone output for the Surround mode.
CNTR TONE: Selects the center tone level for the Surround/DVD MULTI
playback modes.
CD player
After pressing CD (with the remote control mode selector set to “AUDIO/TV/VCR”),
you can perform the following operations on a CD player:
PLAY: Starts playing.
44
44
4: Returns to the beginning of the current (or previous) track.
¢¢
¢¢
¢: Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Pauses playing. To release it, press PLAY.
1 — 10, +10: Selects a track number directly.
For track number 5, press 5. For track number 15, press +10, then 5. For
track number 20, press +10, then 10. For track number 30, press +10,
+10, then 10.
Notes:
• If you use the buttons on the
front panel or the menu
function to choose a source,
the remote control will not
operate that source. To
operate a source with the
remote control, the source
must be selected using
buttons on the remote control.
• Check to see if its remote
control mode selector is set to
the correct position. To
operate audio system, TVs,
and VCRs, set it to “AUDIO/
TV/VCR.”
• Refer also to the manuals
supplied with your
components.
O
N
S
C
R
E
E
N
C
O
N
T
R
O
L
RM-SR774XU REMOTE CONTROL
/DBS
SOUND
CONTROL
CD
DISC
VCR
SLEEP
AUDIO
DVD MULTI
DVD TV/DBSVCR
CD
SEA
MODE
TEST
(REAR R)
REAR (L)
DELAY
TAPE/MD FM/AMPHONO
546
213
87/P 9
0
+10
10
AUDIO/TV
/VCR
SET EXIT
VCR TAPE
CONTROL
VOLUME
CHANNEL
MUTE
FF / ¢
PLAY
STOP
REC
TV/VIDEO
TV VOLUME
PAUSE
4 / REW
TV/CATV
CNTR
CNTR TONE
ENTER
MENU
EFFECT
CATV
/DBS
FM MODE/MUTE
100+
RETURN
SURROUND
MODE
T
U
N
I
N
G
U
P
T
U
N
I
N
G
D
O
W
N
M
E
N
U
Note:
After adjusting sounds, press
the corresponding source
selecting button or CD DISC to
operate your target source by
using 10 keys; otherwise, 10
keys cannot be used for
operating your target source.
EN47_72.RX-774P[U]/1 98.3.10, 2:55 PM62