Filter
Top Products
15
By pressing the following buttons, you can stop, advance, or reverse
playback, and locate the beginning of the title, chapter, or track.
To stop playback temporarily
Press 8.
• Pressing 3 starts playback again.
To move back the playback position by 10 seconds
(for DVD VIDEO only)
Press 3 during DVD VIDEO playback.
The unit moves the playback position about 10 seconds before the
current position, then resumes playback.
To advance or reverse playback rapidly
Press and hold ¢ or 4.
While you are pressing and holding ¢ (or 4), the unit advances
(or reverses: for DVD VIDEO and audio CD) playback 5 times as
fast as the normal speed. When you press and hold ¢ (or 4)
further, the playback speed changes up to 20 times as fast as the
normal speed.
• Releasing the button resumes the normal playback.
To locate the beginning of the chapter, or track
Press ¢ or 4.
Press ¢ (or 4) to locate the beginning of the next (current or
previous) chapter, or track.
To locate the chapter or track using number buttons
Press number buttons (1–10, +10) to select the number of the
desired chapter or track.
Ex. : To select 3, press 3.
To select 11, press +10, then 1.
To select 20, press +10, then 10.
Basic DVD Player Operations
For details about DVD player operations, see pages 29 to
42.
• You can also play back MP3 and JPEG files. See pages 43
to 46.
1
Open the Disc Tray
Before turning on the unit, turn on your TV and select the correct
video input (see the manual supplied with your TV).
• When you use a JVC’s TV, you can turn on your TV by pressing
STANDBY/ON TV on the remote control and select the
video input by pressing TV/VIDEO. (If your TV is not a JVC’s,
see “Operating Other Manufacturers’ Equipment” on page 61.)
• For changing the OSD messages—the information on the TV
—into the desired language, see pages 47 and 49.
Press 0.
The unit is turned on and the disc tray opens.
The STANDBY lamp goes off and the illumination lamp lights up.
• When a disc is already loaded, pressing 3 turns on the unit and
starts playing back the loaded disc.
2
Load a Disc
Place a disc correctly with its label side up.
• When using remote control, press DVD to change the
remote control operation mode to the DVD player
operation.
REW/( TUNING
9/FF
FM MODE STROBE
– TV/DBS CH +
From the front panel ONLY
RX-DV3 HOME THEATER DVD/CD RECEIVER
TAPE/CDR
SOURCE NAME
TV
VCR
DBS
DVD
STANDBY
S
T
AN
D
B
Y
/O
N
IN
P
U
T A
TT.
INPUT
ANALOG/DIGITAL
D
I
G
IT
A
L
S
U
R
R
O
U
N
D
O
N
/OF
F
SURROUND
M
O
D
E
CORRECT
INCORRECT
3
Start Playback
Press 3.
The disc tray closes and the unit starts playing back the loaded disc.
• You can also close the disc tray by pressing 0 on the front panel.
TUNING
On the front panel From the remote control
About indication on the display while playing back a disc
While you are playing back a disc, the playback information
appears on the display as follows:
Ex.: When DVD VIDEO is loaded
Ex.: When audio CD is loaded
Track number Elapsed playing time
SPK.
DIGITAL AUTO
VOLUME
PRO LOGIC
LR
SUBWFR
From the remote control ONLY
231
564
89
7
10/0 +10
100+
EFFECT
TEST
SURR ON/OFF
SURR MODE
–
SUBWOOFER
+
CENTER
REAR·L
REAR·R
DIGITAL AUTO
VOLUME
DIGITAL
AUTO
SURROUND
SPK.
LFE
LS RS
LCR
SUBWFR
Chapter number Elapsed playing time
On the front panel
From the remote control
EN15-18RX-DV3SL[J]f.pm5 02.4.19, 16:0015