JVC RX-8020VBK Stereo Receiver User Manual


 
41
English
5. Press SOUND again then repeat steps 3
and 4 to adjust the other speakers
output levels.
6. Press TEST again to stop the test
tone.
Notes:
If you have selected NO or NONE for a speaker (see page 22),
test tone does not come out of the corresponding speaker.
Subwoofer output level cannot be adjusted when
outputting test tone. When you adjust the
subwoofer output level, press SOUND, SUBWFR
then LEVEL + or to adjust the speaker output
level (10 dB to +10 dB). (S-WFR appears on the
remote control display window.)
It is recommended to make adjustments while listening to the
sound of the source played back.
Test tone does not output through the speakers when selecting
DVD MULTI.
On the front panel:
You can also use the buttons on the front panel to adjust the speaker
output levels. However, no test tone is available when using the
buttons on the front panel. So make adjustments while listening to
the sound of the source played back.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1. Press LEVEL ADJUST repeatedly to
select a speaker you want to adjust.
Each time you press the button, the items change
as follows.
SUBWFR (Subwoofer)
=
FRNT L (Left front speaker)
=
CENTER (Center speaker)
=
FRNT R (Right front speaker)
=
SURR R (Right surround speaker)
=
SBK R (Right surround back speaker)
* =
SBK L (Left surround back speaker) or
S BACK (surround back speaker)
* =
SURR L (Left surround speaker)
=
(Back to the beginning)
*
If you have selected 1SPK for the surround back speaker (see
page 22), S BACK appears instead of SBK L and SBK R.
2. Press CONTROL UP 5 or
DOWN to adjust the speaker
output level (10 dB to +10 dB).
3. Repeat steps 1 and 2 to adjust the
other speakers output levels.
From the remote control:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
Adjustment is also possible without outputting the test tone. In this
case, you can skip steps 2 and 6 below.
1. Press SOUND.
SOUND appears on the remote control display
window.
The 10 keys are activated for sound adjustments.
2. Press TEST to
check if you can
hear the sounds through all the
speakers at equal level.
A test tone comes out of the speakers (only if the speakers are
activated) in the following order:
FRNT L (Left front speaker)
=
CENTER (Center speaker)
=
FRNT R (Right front speaker)
=
SURR R (Right surround speaker)
=
SBK R (Right surround back speaker)
* =
SBK L (Left surround back speaker) or
S BACK (surround back speaker)
* =
SURR L (Left surround speaker)
=
(Back to the beginning)
*
If you have selected 1SPK for the surround back speaker (see
page 22), S BACK appears instead of SBK L and SBK R.
No test tone outputs from the right surround back speaker.
3. Select a speaker you want to adjust.
The selected speaker name appears on
the remotes display for a while.
To select the left front speaker, press
FRONTL. FRL appears on the
remote control display window.
To select the center speaker, press
CENTER. CTR appears on the
remote control display window.
To select the right front speaker,
press FRONTR. FRR appears on
the remote control display window.
To select the right surround speaker, press SURRR.
SURRR appears on the remote control display window.
To select the right surround back speaker, press SBACKR.
SBKR appears on the remote control display window.
To select the left surround back speaker, press SBACKL.
SBKL appears on the remote control display window.
To select the left surround speaker, press SURRL. SURRL
appears on the remote control display window.
Note:
If you have selected 1SPK for the surround back speaker (see
page 22), press SBACKL to adjust the surround back speaker
output level.
4. Press LEVEL + or to adjust the
speaker output level (10 dB to
+10 dB).
SOUND
MENU
4
TEST
23
56
89
0
+10
FRONTL
MENU
ENTER
FRONTR
CENTER
SUBWFR
Q
SBACKL
SBACKR
SURRL
SURRR
FM MODE 100
+
MENU
4
TEST
SOUND
6
SUBWFR
+
CH/
LEVEL
L
LEVEL
ADJUST
CONTROL
DOWN UP
EN38-42.RX-8020V[C]_f 02.4.3, 0:29 PM41