Filter
Top Products
40
English
Using the on-screen display (through the remote control]:
Adjustment is also possible without outputting the test tone. In this
case, you can skip steps 2, 3 and 7 below.
1. Show LEVEL ADJUST menu (see page 38).
2. Press 5 or ∞ to move
to “TEST TONE.”
3. Press 2 or 3 to select “ON”
to check if you can
hear the sounds through all the speakers at equal
level.
A test tone comes out of the speakers (only if the speakers are
activated) in the following order:
FRONT L (Left front speaker)
=
CENTER (Center speaker)
=
FRONT R (Right front speaker)
=
SURR R (Right surround speaker)
=
S BACK R (Right surround back speaker)
* =
S BACK L (Left surround back speaker) or
S BACK (Surround back speaker)
* =
SURR L (Left surround speaker)
=
(Back to the beginning)
*
If you have selected “1SPK” for the surround back speaker (see
page 22), “S BACK” appears instead of “S BACK L” and
“S BACK R.” No test tone outputs from the right surround back
speaker.
4. Press 5 or ∞ to move to a speaker you want
to adjust.
5. Press 2 or 3 to adjust the speaker output level
(–10 dB to +10 dB).
6. Repeat steps 4 and 5 to adjust the other speakers
output levels.
7. After the adjustment is finished, press 5 or ∞ to
move
to “TEST TONE,” then select “OFF.”
8. When you finish, press EXIT repeatedly until the
menu disappears from the TV.
Notes:
• If you have selected “NO” or “NONE” for a speaker (see page 22),
test tone does not come out of the corresponding speaker.
• Subwoofer output level cannot be adjusted when outputting test
tone. When you adjust the subwoofer output level, select “OFF” for
“TEST TONE.”
• Test tone does not output through the speakers when selecting
DVD MULTI.
7
Adjustable speakers
You can adjust the following speakers’ output levels within the
range of –10 dB to +10 dB (“0 dB” is the initial setting):
Notes:
*
If you have selected “1SPK” for the surround back speaker (see
page 22), “S BACK” appears instead of “S BACK (SBK) L” and
“S BACK (SBK) R.” No test tone outputs from the right surround
back speaker.
• If you have selected “NO” or “NONE” for a speaker (see page
22), the output level for the corresponding speaker cannot be
adjustable.
• The center and left and right surround speakers’ output levels
are adjustable for DVD MULTI playback mode, even though
“NONE” is selected for the speaker settings.
• Speaker output levels except that of the subwoofer are not
adjustable when Analog Direct is in use.
SUBWFR :
FRONT L (FRNT L):
CENTER :
FRONT R (FRNT R):
SURR R :
S BACK R (SBK R) *:
S BACK L (SBK L) :
or S BACK*
SURR L :
Select this to adjust the subwoofer
output level.
Select this to adjust the left front
speaker output level.
Select this to adjust the center
speaker output level.
Select this to adjust the right front
speaker output level.
Select this to adjust the right
surround speaker output level.
Select this to adjust the right
surround back speaker output level.
Select this to adjust the left surround
back speaker output level.
Select this to adjust the left surround
speaker output level.
Adjusting the Speaker Output Levels
—LEVEL ADJUST
You can adjust the speaker output levels. The test tone can be also
output from each speaker except subwoofer to check the output level
balance when using the Surround mode.
• Once you have made adjustment, it is memorized for each source.
• When using the buttons on the front panel to adjust output level
for the Surround mode, no test tone is available.
EN38-42.RX-8020V[C]_f 02.4.3, 0:29 PM40