Filter
Top Products
122
Controlling Other Components
—Continued
The AV receiver’s remote controller can learn the com-
mands of other remote controllers. By transmitting, for
example, the Play command from your CD player’s
remote controller, the remote controller can learn it, and
then transmit the exact same command when its Play
[] button is pressed in the CD remote mode.
This is useful when you’ve entered the appropriate
remote control code (page 119) but some buttons don’t
work as expected.
Notes:
• The following buttons cannot learn new commands:
Remote Mode, Macro [1], [2], [3], TV CH [+]/[–], Re-
EQ, Light.
• When you want to learn the command from your TV’s
Power button, select the TV remote control mode and
use the remote controller’s [Standby] button to learn
the command. In the TV remote control mode, the
remote controller’s [Standby] and TV [ ] buttons
are linked, so using the [Standby] button to learn the
command will mean that you can also use the TV
[] button to turn your TV on or off in TV remote
control mode.
• When you want to learn the commands from your
TV’s Channel Up and Down buttons, select the TV
remote control mode and use the remote controller’s
CH [+/–] button (left to the [Enter] button) to learn the
commands. In the TV remote control mode, the
remote controller’s CH [+/–] and TV CH [+]/[–] but-
tons are linked, so using the CH [+/–] button to learn
these commands will mean that you can also use the
TV CH [+]/[–] buttons to change channels in TV
remote control mode.
• The remote controller can learn approximately 70 to
90 commands, although this will be less if commands
that use a lot of memory are learned.
• Remote controller buttons such as Play, Stop, Pause,
and so on are preprogrammed with commands for
controlling Onkyo CD players, cassette decks, and
DVD players. However, they can learn new com-
mands, and you can restore the preprogrammed com-
mands at any time by resetting the remote controller
(see page 120).
•To overwrite a previously learned command, repeat
this procedure.
• Only commands from infrared remote controllers can
be learned.
• When the remote controller’s batteries expire, all
learned commands will be lost and will have to be
learned all over again, so don’t discard your other
remote controllers.
Learning Commands
1
While holding down the Remote
Mode button for the mode in
which you want to use the com-
mand, press the [On] button.
The Remote indicator lights up.
2
Press the button you want to
learn the new command.
3
Point the remote controllers at
each other, about 2 to 6 inches
(5–15 cm) apart, and then press
and hold the button whose com-
mand you want to learn until the
Remote indicator flashes.
+
-
On Standby
TV
Input
TV CH
TV VOL
--
/
---
10 11 12
D.TUN
+10
0
Clear
123
456
789
Input Selector
VCR
/
DVR CBL
/
SAT
DVD
Tape
Tuner
CD
Phono
Game
/
TV
Macro
12
3
VCRDVD
CDR/MD
CD
Zone
2
Remote Mode
Dimmer
Tape/AMP
Sleep
Receiver
TV Dock
Cable
VOL
CH
Disc
Album
+
-
Enter
T
o
p
M
e
n
u
M
e
n
u
Display Muting
E
x
i
t
G
u
i
d
e
Prev
CH
R
e
t
u
r
n
S
e
t
u
p
SAT
Zone
3
AUX 1 AUX 2
1, 4
1
Remote
indicator
VCRDVD
CDR/MD
CD
Remote Mode
Tape/AMP
Receiver
TV
Dock
Cable
SAT
On
If the command is learned successfully,
the Remote indicator flashes twice.
4
To learn more commands, repeat
steps 2 and 3.
Press any Remote Mode button when
you’ve finished.
POWER
SLEEP
DIMMER
SUR
M
ODE
VIDEO-1
VIDEO-2
TAPE
DVD
C D
C D
DVD
TU
NER
TUNER
PHONO
INPUT SELECTOR
DISC
TAPE
VOLUME
EVEL
CH SEL
PRESET
MUTING
TEST
TONE
MULTI-CH
INPUT
GROUP
R
1
0
-
-
/--
-
1
1
1
2
R
em
ote
M
ode
Z
o
n
e
2
DVD
VCR
CD
Z
o
n
e
3
Receiver
Cable
D
oc
k
Tap
e/A
M
P
SAT
CDR/MD
+
-
T
V
C
H
T
V
V
O
L
Sleep
Input Selector
3
2
Macro
1
+
10
0
Clear
D
.TU
N
1
2
3
4
5
6
7
8
9
In
p
u
t
I
O
n
S
ta
n
d
b
y
T
V
T
a
p
e
D
V
D
D
C
R
/D
V
R
C
B
L
/S
A
T
AUX1
A
U
X
2
T
u
n
e
r
C
D
Phono
G
a
n
e
/T
V
About 2 to 6
inches (5–15 cm)
RC-691M