Filter
Top Products
34
Programming the remote controller codes
of other devices into the RC-424M
The RC-424M has two learning functions. One is a normal learning function that enables the RC-424M to learn other
remote controllers’ codes. The other is a macro learning function, which enables the RC-424M to learn a series of
codes already memorized in the remote controller into one MACRO button.
Program the codes for each mode (AUDIO, CD, DVD, MD, SAT, CABLE, VCR, and TV).
1. Place the RC-424M and the remote controller for
another device, with 5–15cm (2–6 inches) apart and
the light-emitting parts facing each other.
2. While pressing and holding down the desired MODE
button on the RC-424M (AUDIO, CD, DVD, MD, SAT,
CABLE, VCR, or TV), press the ENT button, then release
the buttons.
When you press and hold down one of the MODE
button, the SEND/LEARN indicator lights up. When
you press the ENT button, the indicator turns off.
When you release the buttons, the SEND/LEARN indi-
cator lights up again.
3. Press and release the desired operation button on
the RC-424M.
You may select any button within the rectangle shown
in the figure. When you press the button, the SEND/
LEARN indicator turns off. When you release the button,
the indicator lights up again.
4. Press and hold down the desired button on the
remote controller of the other device until the SEND/
LEARN indicator on the RC-424M flashes twice.
The SEND/LEARN indicator flashes twice slowly, then
lights up.
5. Repeat Steps 3–4 to program other buttons in the
same MODE.
Repeat Steps 2-4 to program other buttons in a differ-
ent MODE.
6. Press the MODE button to complete programming.
7. Operate the programmed button to make sure the
learning function works.
Note:
The remote controller codes for the Integra/Onkyo CD
player, DVD player, Onkyo tape deck and MD recorder
have already been programmed into the buttons on
the RC-424M. You may program other remote controller
codes into these buttons. If you wish to restore the Inte-
gra/Onkyo preset codes after you program new codes,
erase the new codes. (See page 35.)
Note:
• The remote controller has 408 memory slots (51 but-
tons × 8 modes), although this number varies signifi-
cantly depending on the manufacturers and types of
the remote controller you wish to program into the RC-
424M. It is recommended that you determine which
button functions have priority for programming.
• If you do not press any button for more than 30 sec-
onds during the procedure, the SEND/LEARN indicator
flashes three times quickly, then the RC-424M exits
Learning mode. Resume Step 2.
• If you make a mistake during programming, the
SEND/LEARN indicator flashes three times quickly,
then the RC-424M exits Learning mode.
• If you try to program beyond the learning capacity
of the RC-424M, the SEND/LEARN indicator flashes six
times quickly, then the RC-424M exits Learning func-
tion. Try programming in a button of other MODE.
• Follow the same procedure when you wish to program
new codes into the already-programmed buttons.
• This remote controller uses infrared rays. Most remote
controller codes can be memorized using the infra-
red system; however, depending on the degree to
which the system differs, there may be some rare
occasions when memorization is not possible.
• Some remote controllers use a single button to per-
form different functions, with the function code
changing each time the button is pressed. If you are
using this kind of controller, please perform the
“learn” operations for each function individually to
store each function to a button on the RC-424M.
• For instructions regarding the operation of “learned” units,
please refer to the instruction manual for each product.
• Even after codes have been memorized, please
keep your old remote controller in a safe place. If the
memorized codes are lost when the batteries run
down, it will be necessary to memorize them once
again using the old remote controller.
• Make sure both the RC-424M and the product’s own
remote controller have fresh batteries. If either of
them has batteries that are wearing down, it may be
impossible to store the remote controller codes into
the RC-424M or the product may not respond prop-
erly to the buttons on the RC-424M for which the
remote controller codes were stored into memory.
Programming procedure
1
3
2
6
4
Light
5 to 15 cm
(2 to 6 inches)
The button you wish to memorize
RC-424M
HOME THEATER CONTROLLER
RC-424M