Filter
Top Products
59
Advanced Setup
—Continued
■
e. Virtual Surr Level
With this setting, you can adjust the level of virtual sur-
round sound from –3 dB to +3 dB (default is 0 dB). If the
clarity is poor, or the effect sounds unnatural, you may
be able to improve it by lowering this setting.
You can assign a default listening mode to each input
source that will be selected automatically when you
select each input source. For example, you can set the
default listening mode to be used with Dolby Digital
input signals. You can select other listening modes dur-
ing playback, but the mode specified here will be
resumed once the AV receiver has been set to Standby.
Note:
• This procedure can also be performed on the AV
receiver by using its [Setup] button, arrow buttons, and
[Enter] button.
Assigning Listening Modes to Input
Sources
1
Press the [Receiver] button fol-
lowed by the [Setup] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select “5. Listening
Mode Preset,” and then press
[Enter].
The Listening Mode Preset menu
appears.
3
Use the Up and Down [ ]/[ ]
buttons to select the input selec-
tor that you want to set, and then
press [Enter].
For input selectors that have no digital
input jacks, only “a. Analog” will be
available.
Receiver
Enter
Enter
Menu
------------------------
1.Initial Setup
2.Speaker Setup
Advanced Setup
3.Surround Setup
4.Audio Adjust
5.Listening Mode Preset
6.Preference
Basic Setup
5.Listening Mode Preset
------------------------
2.VIDEO1
3.VIDEO2
4.VIDEO3
5.TAPE
6.TUNER
7.CD
1.DVD/MULTICH
Enter
Enter
5-1.ListeningModePreset
a.Ana/PCM :Last Valid
----- DVD/MULTICH ------
b.Dolby D :Last Valid
c.DTS :Last Valid
d.D.F.2ch :Last Valid
e.D.F.Mono:Last Valid
f.Multiplex
:Last Valid
g.Multich :Last Valid
4
Use the Up and Down [ ]/[ ]
buttons to select the signal for-
mat that you want to set, and
then use the Left and Right [ ]/
[] buttons to select a listening
mode.
Only listening modes that can be used
with each input signal format can be
selected.
The Last Valid option means that the
listening mode selected last will be
used.
For “Surround”, the listening mode
specified on pages 56, 57.
a. Ana/PCM:
With this setting, you
can specify the listening mode to be
used when an analog (CD, TV, LD,
VHS, MD, turntable, radio, cassette,
cable, satellite, etc) or PCM digital
(CD, DVD, etc) audio signal is played.
b. Dolby D:
With this setting, you can
specify the listening mode to be used
when a Dolby Digital format digital
audio signal is played (DVD, etc).
c. DTS:
With this setting, you can spec-
ify the listening mode to be used when
a DTS format digital audio signal is
played (DVD, LD, CD, etc).
d. D.F. 2ch:
With this setting, you can
specify the listening mode to be used
when a 2-channel (2/0) digital audio
signal (Dolby Digital, DTS) is played
(DVD, etc).
e. D.F. Mono:
With this setting, you
can specify the listening mode to be
used when a mono digital audio signal
is played (DVD, etc).
f. Multiplex:
With this setting, you can
specify the listening mode to be used
when a multiplex audio signal is
played.
g. Multich:
This setting is available
only when “5-1. DVD/MULTCH” is
selected. With this setting, you can
specify the listening mode to be used
when the DVD analog multichannel
input is used.
5
When you’ve finished, press the
[Setup] button.
The setup menu closes.
Enter