Filter
Top Products
29
ENGLISH
[3]Setting the channel level
• Use this setting to adjust so that the playback level between the
different channels is equal.
• From the listening position, listen to the test tones produced from
the speakers to adjust the level.
• The level can also be adjusted directly from the remote control unit.
(For details, see page 40.)
1
To perform these operations from places other than the
system setting change menu, see page 26.
2
At the SYSTEM SETUP MENU select “CHANNEL LEVEL”.
• Switch to the CHANNEL LEVEL screen.
3
Select “TEST TONE MODE”.
• Select the mode.
Select “AUTO” or “MANUAL”.
• AUTO: Adjust the level while listening to the test tones produced
automatically from the different speakers.
• MANUAL: Select the speaker from which you want to produce the
test tone to adjust the level.
4
If “YES” is selected at “LEVEL CLEAR”, the level settings for
all the speakers are set to 0 dB.
B “YES” : The levels of the different speakers are all set to 0dB.
B “NO” : The speakers stay at their currently set levels.
5
Adjusting the channel levels in the “test tone” mode
• Set the “TEST TONE START” mode using the and
cursor buttons, then select “YES” with the cursor
button to output test tones.
6
q When “AUTO” is selected in the “TEST TONE MODE”
• Test tones are automatically emitted from the different speakers.
• The test tones are emitted from the different speakers in the
following order, at 4-second intervals the first time and second
time around, 2-second intervals the third time around and on:
•
Use the CURSOR buttons to adjust all the speakers to the same volume.
•
The volume can be adjusted between –12 dB and +12 dB in units of 1 dB.
w When the “MANUAL” mode is selected
• Use the CURSOR left and right to select the speaker for which you
want to output test tones, then use the CURSOR up and down to
adjust so that the volume of the test tones from the various
speakers is the same.
7
After the above settings are completed, press the ENTER
button.
• The “SYSTEM SETUP MENU” screen reappears.
To cancel the setting after adjusting
Display the channel level adjustment screen, then use the ,
, and cursor buttons to select “LEVEL CLEAR” and
“YES”. The level settings for all the speakers are set to 0 dB.
NOTE:
• When you adjust the channel levels while in the SYSTEM SETUP
CHANNEL LEVEL mode, the channel level adjustments made
will affect ALL surround modes. Consider this mode a Master
Channel Level adjustment mode.
• After you have completed the SYSTEM SETUP CHANNEL LEVEL
adjustments, you can then activate the individual surround
modes and adjust channel levels that will be remembered for
each of those modes. Then, whenever you activate a particular
surround sound mode, your preferred channel level adjustments
for just that mode will be recalled. Check the instructions for
adjusting channel levels within each surround mode on page 40.
B
0 d B0 d B
0 d B0 d B
0 d B0 d B
0 d B0 d B
0 d B0 d B
FINISH: ENTER BUTTON
CHANNEL LEVEL
SELECT :
AUTOAUTO MANUALMANUAL
TEST TONE MODETEST TONE MODE
TEST TONE STARTTEST TONE START
FRONT LFRONT L
CENTERCENTER
FRONT RFRONT R
SURROUND RSURROUND R
SURROUND LSURROUND L
SUBWOOFERSUBWOOFER
LEVEL CLEARLEVEL CLEAR
0 d B0 d B
B
YESYES
0 d B0 d B
0 d B0 d B
0 d B0 d B
0 d B0 d B
0 d B0 d B
FINISH: ENTER BUTTON
CHANNEL LEVEL
SELECT :
AUTOAUTO MANUALMANUAL
TEST TONE MODETEST TONE MODE
TEST TONE STARTTEST TONE START
FRONT LFRONT L
CENTERCENTER
FRONT RFRONT R
SURROUND RSURROUND R
SURROUND LSURROUND L
SUBWOOFERSUBWOOFER
LEVEL CLEARLEVEL CLEAR
+ +
1 0 d B1 0 d B
B
YESYES
0 d B0 d B
0 d B0 d B
0 d B0 d B
0 d B0 d B
0 d B0 d B
FINISH: ENTER BUTTON
CHANNEL LEVEL
SELECT :
AUTO AUTO MANUALMANUAL
TEST TONE MODETEST TONE MODE
TEST TONE STARTTEST TONE START
FRONT LFRONT L
CENTERCENTER
FRONT RFRONT R
SURROUND RSURROUND R
SURROUND LSURROUND L
SUBWOOFERSUBWOOFER
LEVEL CLEARLEVEL CLEAR
+ +
1 0 d B1 0 d B
ENTER
Front L Center Front R
Surround RSurround LSubwoofer
Remote control unit Remote control unit
Remote control unit